This is the repair procedure for the accelerator pedal sensor assembly.
This electrical throttle system does not use a throttle cable.
This accelerator pedal position sensor is a non-contact type.
The accelerator pedal position sensor is mounted on the accelerator pedal sensor assembly and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator pedal position sensor.
In the accelerator pedal position sensor, the voltage applied to terminals VPA and VPA2 of the ECM changes between 0.5 V and 4.8 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for engine control, and the VPA2 is a signal to indicate information about the opening angle which is used for detecting malfunctions. The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the injection volume based on these signals.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P212012 | Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Auxiliary Battery | VPA is 4.8 V or higher for 2 seconds or more. (1 trip detection logic) |
·
Accelerator pedal sensor assembly
·
Open in EPA circuit
·
Short in VPA circuit
·
ECM |
Comes on | SAE Code: P2123 |
| P212014 | Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open | VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is depressed. (1 trip detection logic) |
·
Accelerator pedal sensor assembly
·
Open in VCPA circuit
·
VPA circuit open or shorted to ground
·
ECM |
Comes on | SAE Code: P2122 |
| P21201C | Throttle/Pedal Position Sensor/Switch "D" Circuit Voltage Out of Range | Difference between VPA and VPA2 is greater than or equal to the specified value for 2 seconds. (1 trip detection logic) |
·
Accelerator pedal sensor assembly
·
ECM |
Comes on | SAE Code: P2121 |
| P21201F | Throttle/Pedal Position Sensor/Switch "D" Circuit Intermittent | VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more. (1 trip detection logic) |
·
Accelerator pedal sensor assembly
·
Accelerator pedal sensor assembly circuit
·
ECM |
Comes on | SAE Code: P2120 |
| P212099 | Throttle/Pedal Position Sensor/Switch "D" Exceeded Learning Limit | Difference between VPA and VPA2 is less than 0.4 V, or higher than 1.2 V (learned value of accelerator off position). (1 trip detection logic) |
·
Accelerator pedal sensor assembly
·
ECM |
Comes on | SAE Code: P2121 |
| P212512 | Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Auxiliary Battery | Both of the following conditions are met for 2 seconds or more: (a) VPA2 is 4.8 V or higher. (b) VPA is between 0.4 V and 3.45 V. (1 trip detection logic) |
·
Accelerator pedal sensor assembly
·
Open in EPA2 circuit
·
Short in VPA2 circuit
·
ECM |
Comes on | SAE Code: P2128 |
| P212514 | Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open | VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is depressed. (1 trip detection logic) |
·
Accelerator pedal sensor assembly
·
Open in VCP2 circuit
·
VPA2 circuit open or shorted to ground
·
ECM |
Comes on | SAE Code: P2127 |
| P21251F | Throttle/Pedal Position Sensor/Switch "E" Circuit Intermittent | VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more. (1 trip detection logic) |
·
Accelerator pedal sensor assembly
·
Accelerator pedal sensor assembly circuit
·
ECM |
Comes on | SAE Code: P2125 |
| P21382B | Throttle/Pedal Position Sensor/Switch "D"/"E" Signal Cross Coupled | Difference between VPA and VPA2 is 0.02 V or less for 2.0 seconds or more. (1 trip detection logic) |
·
Accelerator pedal sensor assembly
·
Accelerator pedal sensor assembly circuit
·
ECM |
Comes on | SAE Code: P2138 |
| DTC No. | Data List |
|---|---|
| P212012 P212014 P21201C P21201F P212099 P212512 P212514 P21251F P21382B |
·
Accel Position
·
Accelerator Position Sensor No.1 Voltage %
·
Accelerator Position Sensor No.2 Voltage % |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P212012 P212014 P21201C P21201F P212099 P212512 P212514 P21251F P21382B |
Ignition switch ON
·
Accelerator pedal fully released for 3 seconds
·
Accelerator pedal depressed partway for 3 seconds
·
Accelerator pedal fully depressed for 3 seconds |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Enter the following menus: Powertrain / Engine / Data List / Primary / Accelerator Position Sensor No.1 Voltage % and Accelerator Position Sensor No.2 Voltage %.
| Tester Display |
|---|
| Accelerator Position Sensor No.1 Voltage % |
| Accelerator Position Sensor No.2 Voltage % |
| *1 | Accelerator Pedal Sensor Assembly |
| *a | Depressed |
| *b | Released |
Read the values.
| Accelerator Pedal | Accelerator Position Sensor No.1 Voltage % | Accelerator Position Sensor No.2 Voltage % |
|---|---|---|
| Released | 10 to 22% | 24 to 40% |
| Depressed | 52 to 90% | 68 to 99% |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B17,B70)Location & Routingewd_type=routing;type=c,c;code=B17,B70 Click Connector(B17)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Accelerator Pedal with Sensor Rod Assemblyewd_type=component;type=c;code=B17;pinno=6,5,4,3,2,1 |
||
| B17-6 (VPA) - B70-55 (VPA) | Always | Below 1 Ω |
| B17-5 (EPA) - B70-56 (EPA) | Always | Below 1 Ω |
| B17-4 (VCPA) - B70-57 (VCPA) | Always | Below 1 Ω |
| B17-3 (VPA2) - B70-58 (VPA2) | Always | Below 1 Ω |
| B17-2 (EPA2) - B70-59 (EPA2) | Always | Below 1 Ω |
| B17-1 (VCP2) - B70-60 (VCP2) | Always | Below 1 Ω |
| B17-6 (VPA) or B70-55 (VPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| B17-5 (EPA) or B70-56 (EPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| B17-4 (VCPA) or B70-57 (VCPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| B17-3 (VPA2) or B70-58 (VPA2) - Body ground and other terminals | Always | 10 kΩ or higher |
| B17-2 (EPA2) or B70-59 (EPA2) - Body ground and other terminals | Always | 10 kΩ or higher |
| B17-1 (VCP2) or B70-60 (VCP2) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the accelerator pedal sensor assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B17)Location & Routingewd_type=routing;type=c;code=B17 Click Connector(B17)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Accelerator Pedal with Sensor Rod Assemblyewd_type=component;type=c;code=B17;pinno=4,5,1,2 |
||
| B17-4 (VCPA) - B17-5 (EPA) | Ignition switch ON | 4.5 to 5.5 V |
| B17-1 (VCP2) - B17-2 (EPA2) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the accelerator pedal sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B17)Location & Routingewd_type=routing;type=c;code=B17 Click Connector(B17)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Accelerator Pedal with Sensor Rod Assemblyewd_type=component;type=c;code=B17;pinno=4,6,5,1,3,2 |
||
| B17-4 (VCPA) - B17-6 (VPA) | Ignition switch off | No short or no open circuit |
| B17-6 (VPA) - B17-5 (EPA) | Ignition switch off | No short or no open circuit |
| B17-1 (VCP2) - B17-3 (VPA2) | Ignition switch off | No short or no open circuit |
| B17-3 (VPA2) - B17-2 (EPA2) | Ignition switch off | No short or no open circuit |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the accelerator pedal sensor assembly.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and leave the vehicle for 30 seconds.
Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT