| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P24A571 | Exhaust Gas Recirculation Cooler Bypass Control Stuck/Open Bank 1 Actuator Stuck | Either of the following conditions is met:
·
A change in the opening angle of the EGR cooler bypass valve of less than the specified value (1.75%) continues for 22 seconds or more, even if the drive duty ratio of the EGR cooler bypass valve exceeds the threshold (-80 to 80%) with the ignition switch turned to ON or the engine running
·
The drive duty ratio of the EGR cooler bypass valve exceeds the threshold (-88 to 88%) with the ignition switch turned to ON or the engine running, and the condition that a motor current value of the specified value (1 A) or more continues for 0.5 seconds occurs the specified number of times (39.5 seconds or more in real time). (1 trip detection logic) |
·
No. 2 EGR valve assembly (EGR cooler bypass valve) stuck
·
No. 2 EGR valve assembly (EGR cooler bypass valve) does not move smoothly
·
No. 2 EGR valve assembly (EGR cooler bypass valve) deposit |
Comes on | SAE Code: P24A5 |
| DTC No. | Data List |
|---|---|
| P24A571 |
·
EGR Cooler Bypass Valve Request Position
·
EGR Cooler Bypass Valve Position
·
EGR Cooler Bypass Valve Duty Ratio
·
EGR Cooler Bypass Valve Motor Current
·
EGR Temperature B1S1 |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P24A571 | Check that "EGR Cooler Bypass Valve Position" follows "EGR Cooler Bypass Valve Request Position" when performing the Active Test. |
Refer to DTC P249211.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>P249211
When cleaning the electric EGR control valve assembly, No. 2 EGR valve assembly or diesel throttle body assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in solvent may damage the parts.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P24A571 is output | A |
| DTC P24A571 and other DTCs are output | B |
If any DTCs other than P24A571 are output, troubleshoot those DTCs first.
A
B
Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Cooler Bypass Control Valve / Data List / EGR Cooler Bypass Valve Request Position and EGR Cooler Bypass Valve Position.
| Active Test Display |
|---|
| Control the EGR Cooler Bypass Control Valve |
| Data List Display |
|---|
| EGR Cooler Bypass Valve Request Position |
| EGR Cooler Bypass Valve Position |
Read the value displayed on the GTS when the Active Test was performed
The EGR Cooler Bypass Valve Position value follows the EGR Cooler Bypass Valve Request Position value.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 2 EGR valve assembly (EGR cooler bypass valve).
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL
Reconnect the No. 2 EGR valve assembly (EGR cooler bypass valve) connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Cooler Bypass Control Valve.
| Tester Display |
|---|
| Control the EGR Cooler Bypass Control Valve |
Check if the valve of the No. 2 EGR valve assembly (EGR cooler bypass valve) opens/closes when an Active Test is performed.
The valve opens/closes.
| Proceed to |
|---|
| OK |
| NG |
Reinstall the No. 2 EGR valve assembly (EGR cooler bypass valve).
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EGR VALVE>INSTALLATION
OK
NG
Remove the No. 2 EGR valve assembly (EGR cooler bypass valve).
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL
Visually check the No. 2 EGR valve assembly (EGR cooler bypass valve) for deposits. If there are deposits, clean the No. 2 EGR valve assembly (EGR cooler bypass valve).
Do not forcibly open the valve, as it may be damaged or deformed.
When cleaning the No. 2 EGR valve assembly (EGR cooler bypass valve), use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.
When cleaning the No. 2 EGR valve assembly (EGR cooler bypass valve), care should be taken to prevent the ingress of cleaning solvent into the bearings of the valve shaft, and when wiping off deposits on the valve, care should be taken not to push the deposits into the bearings of the valve shaft. These contaminants may adversely affect the function of the valve.
Reinstall the No. 2 EGR valve assembly (EGR cooler bypass valve).
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EGR VALVE>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Cooler Bypass Control Valve / Data List / EGR Cooler Bypass Valve Request Position and EGR Cooler Bypass Valve Position.
| Active Test Display |
|---|
| Control the EGR Cooler Bypass Control Valve |
| Data List Display |
|---|
| EGR Cooler Bypass Valve Request Position |
| EGR Cooler Bypass Valve Position |
Check that "EGR Cooler Bypass Valve Position" follows "EGR Cooler Bypass Valve Request Position" when performing the Active Test.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTCs are not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the No. 2 EGR valve assembly (EGR cooler bypass valve).
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL
Before replacing the No. 2 EGR valve assembly (EGR cooler bypass valve), check the connections of the wire harness and connectors. If there is any abnormality, replace or repair the wire harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT