Refer to DTC P245A18.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>P245A18
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P249211 | Exhaust Gas Recirculation Cooler Bypass Position Sensor Circuit Low Bank 1 Circuit Short to Ground | EGR cooler bypass valve position sensor output is below 0.13 V for 2 seconds. (1 trip detection logic) |
·
No. 2 EGR valve assembly (EGR cooler bypass valve)
·
ECM |
Comes on | SAE Code: P2494 |
| P249215 | Exhaust Gas Recirculation Cooler Bypass Position Sensor Circuit High Bank 1 Circuit Short to Battery or Open | EGR cooler bypass valve position sensor output is higher than 4.89 V for 2 seconds. (1 trip detection logic) |
·
No. 2 EGR valve assembly (EGR cooler bypass valve)
·
ECM |
Comes on | SAE Code: P2495 |
| DTC No. | Data List |
|---|---|
| P249211 P249215 |
·
EGR Cooler Bypass Valve Position
·
EGR Cooler Bypass Valve Position Sensor |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P249211 P249215 |
Ignition switch ON for 2 seconds or more |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Disconnect the No. 2 EGR valve assembly (EGR cooler bypass valve) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C130,C138)Location & Routingewd_type=routing;type=c,c;code=C130,C138 |
||
| C130-2 (VCEC) - C138-91 (VCEC) | Always | Below 1 Ω |
| C130-4 (ECBA) - C138-68 (ECBA) | Always | Below 1 Ω |
| C130-3 (EECB) - C138-90 (EECB) | Always | Below 1 Ω |
| C130-2 (VCEC) or C138-91 (VCEC) - Body ground and other terminals | Always | 10 kΩ or higher |
| C130-4 (ECBA) or C138-68 (ECBA) - Body ground and other terminals | Always | 10 kΩ or higher |
| C130-3 (EECB) or C138-90 (EECB) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 2 EGR valve assembly (EGR cooler bypass valve) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C130)Location & Routingewd_type=routing;type=c;code=C130 |
||
| C130-2 (VCEC) - C130-3 (EECB) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 2 EGR valve assembly (EGR cooler bypass valve) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C130)Location & Routingewd_type=routing;type=c;code=C130 |
||
| C130-2 (VCEC) - C130-4 (ECBA) | Ignition switch off | No short or no open circuit |
| C130-4 (ECBA) - C130-3 (EECB) | Ignition switch off | No short or no open circuit |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 2 EGR valve assembly (EGR cooler bypass valve).
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds.
Turn the ignition switch to ON and wait for 2 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT