Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (w/o Emergency Call Service) › from 2022.11
RM38G0E _56 Audio / Visual / Telematics _100608 TELEMATICS _0562784 TELEMATICS SYSTEM(w/o Emergency Call Service) L

TELEMATICS  TELEMATICS SYSTEM(w/o Emergency Call Service)  PRECAUTION  


PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE




HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


COMMUNICATION FUNCTION PAUSING


NOTICE:
·

Before performing inspections or repairs which may cause warning messages to be displayed or DTCs to be stored, such as a simulation test or road test, it is necessary to enter communication function pausing mode so that unnecessary warning messages are not sent to the service center.

·

After completing maintenance work, be sure to cancel the communication function pausing mode.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (w/o Emergency Call Service)>UTILITY



a.

Communication function pausing mode

i.

Enter communication function pausing mode (Using the GTS) (Method 1)

Enter the following menus: Body Electrical / Telematics

Body Electrical > Telematics > Trouble Codes
50001 459


b.

Enter communication function pausing mode (Using radio receiver assembly) (Method 2)

Enter diagnostic mode of navigation system or audio and visual system.

w/ Navigation System: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

w/o Navigation System (for 12.3 Inch Display): Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, for 12.3 Inch Display)>DTC CHECK / CLEAR

w/o Navigation System (except 12.3 Inch Display): Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>DTC CHECK / CLEAR

HINT:

To cancel communication function pausing mode, turn the ignition switch off and ON to display the service mode screen and cancel communication function pausing mode.




INSPECTION PROCEDURE FOR TELEPHONE TRANSCEIVER ASSEMBLY


a.

The telephone transceiver assembly uses GSM, UMTS and LTE type radio wave signals. Radio waves and telephone network line may occasionally be unstable depending on time or location factors. Therefore, as for the connection malfunction, as there is the possibility of a temporary phenomenon due to the condition of electrical waves, it is necessary to determine by comparing with occurrence frequency or cellular phone.


b.

With the exception of replacing the mobilephone battery, the telephone transceiver assembly cannot be disassembled (the telephone transceiver assembly case must not be opened). Replace parts.



PRECAUTION FOR MOBILEPHONE BATTERY


a.

The mobilephone battery is a Lithium-ion type battery and can be charged from the telephone transceiver assembly.


b.

The mobilephone battery (back-up battery) has a service life of not less than 3 years. When the mobilephone battery needs to be replaced, the LED indicator light indicator (red) will illuminate. The telephone transceiver assembly will also store a Diagnostic Trouble Code (DTC) or vehicle control history (RoB).



PRECAUTION FOR REMOTE SERVICE


NOTICE:

When replacing the telephone transceiver assembly, make sure to replace it with a new one.


a.

If any of the following parts are replaced, refer to Initialization of Repair Instruction.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

Telephone transceiver assembly

·

Certification ECU (smart key ECU assembly)

·

Mobilephone battery



b.

When troubleshooting symptoms such as when part of the remote service function does not operate normally, first check that there are no third party parts connected to the DLC3. If any such parts are connected to the DLC3, some parts of the remote service function may not operate normally.

Therefore, explain the situation to the customer, remove the parts and turn the ignition switch from off to ON before proceeding with troubleshooting.