Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (w/o Emergency Call Service) › from 2022.11
RM38G0E _56 Audio / Visual / Telematics _100608 TELEMATICS _0562784 TELEMATICS SYSTEM(w/o Emergency Call Service) C

TELEMATICS  TELEMATICS SYSTEM(w/o Emergency Call Service)  B157011  Indicator (Red) Circuit Short to Ground  B157013  Indicator (Red) Circuit Open  


DESCRIPTION

This DTC is stored when the telephone transceiver assembly detects an open or short in the LED indicator light indicator (red) circuit of the LED indicator light.

The LED indicator light indicator (red) illuminates for 2 seconds and turns off when the ignition switch is turned to ON.

If a malfunction in the telematics system is detected, the LED indicator light indicator (red) will illuminate. However, the LED indicator light indicator (red) may not illuminate when this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B157011 Indicator (Red) Circuit Short to Ground LED indicator light indicator (red) impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telephone transceiver assembly

·

Map light assembly (LED indicator light)

·

Harness or connector


Telematics A
B157013 Indicator (Red) Circuit Open LED indicator light indicator (red) impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telephone transceiver assembly

·

Map light assembly (LED indicator light)

·

Harness or connector


Telematics A

WIRING DIAGRAM

E354565E87
1.302,0.958 1.76,1.156 0.458,0.198 10 false RED 2.969,0.604 3.292,0.938 0.323,0.333 10 false 15 2.979,1.146 3.292,1.385 0.313,0.24 10 false 5 2.531,0.625 3.146,0.823 0.615,0.198 10 false IND1 2.469,1.156 3.083,1.354 0.615,0.198 10 false GND3 0.865,2.094 1.323,2.292 0.458,0.198 10 false d2 0.854,2.26 2.885,2.688 2.031,0.427 10 false Map Light Assembly 4.938,0.594 5.25,0.792 0.313,0.198 10 false 4 4.938,1.156 5.25,1.354 0.313,0.198 10 false 3 5.167,0.729 5.781,0.927 0.615,0.198 10 false IND1 5.167,1.167 5.781,1.365 0.615,0.198 10 false SIG- 5,2.094 5.938,2.344 0.938,0.25 10 false I55 5,2.25 6.385,2.625 1.385,0.375 10 false Telephone Transceiver Assembly 0.958,1.677 2.99,2.104 2.031,0.427 10 false LED Indicator Light

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (w/o Emergency Call Service)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



HINT:

If DTC B157011 or B157013 is stored, the LED indicator light indicator (red) may not illuminate when another DTC is stored.


PROCEDURE

1.CLEAR DTC

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 10 seconds or more.


Procedure1

b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459
Result:
Proceed to
NEXT



Post-procedure1

c.

None



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Telematics > Trouble Codes
50001 459

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

B

3.INSPECT MAP LIGHT ASSEMBLY (LED INDICATOR LIGHT) (RED INDICATOR)
3.INSPECT MAP LIGHT ASSEMBLY (LED INDICATOR LIGHT) (RED INDICATOR)

Pre-procedure1

a.
E462685C01
1.052,1.406 1.5,1.917 1.5,1.917 1.667,1.917 true 0.865,1.104 1.167,0.333 1.167,0.333 1.333,0.333 true 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 1.396,0.25 1.917,0.469 0.521,0.219 10 false GND3 1.729,1.833 2.167,2.042 0.438,0.208 10 false IND1
*a Component without harness connected
(Map Light Assembly [LED Indicator Light])


Remove the map light assembly (LED indicator light).

HINT:

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL



b.

Connect 2 dry-cell batteries (1.5 V each) in series.


c.

Connect the positive (+) lead to terminal 15 (IND1) and the negative (-) lead to terminal 5 (GND3) of the map light assembly connector.


Procedure1

d.

Check if the illumination for the LED indicator light red indicator comes on.

OK:

Red indicator comes on.


Result:
Proceed to
OK
NG



Post-procedure1

e.

None



OK

4.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY [LED INDICATOR LIGHT])

NG

REPLACE MAP LIGHT ASSEMBLY (LED INDICATOR LIGHT)

4.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY [LED INDICATOR LIGHT])

Pre-procedure1

a.

Disconnect the I55 telephone transceiver assembly connector.


b.

Disconnect the d2 map light assembly (LED indicator light) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I55,d2)Location & Routing

Click Connector(I55)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Telematics Transceiver Assembly

Click Connector(d2)Body>No. 1 Roof Wire>Map Light Assembly (Front)

I55-3 (SIG-) - d2-5 (GND3) Always Below 1 Ω
I55-4 (IND1) - d2-15 (IND1) Always Below 1 Ω
I55-3 (SIG-) - Body ground Always 10 kΩ or higher
I55-4 (IND1) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT