Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2022.11
RM38G0E _51 Engine / Hybrid System _101047 STOP AND START _0469044 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P30DF62  Backup Boost Converter Circuit Board(Thermistor) Signal Compare Failure  P30EF4B  Backup Boost Converter Circuit Board Over Temperature  P323A00  Backup Boost Converter "A"  P323A16  Backup Boost Converter "A" Circuit Voltage Below Threshold  P323AA2  Backup Boost Converter "A" System Voltage Low  P323B29  Backup Boost Converter "A" Control Circuit Signal Invalid  P323B38  Backup Boost Converter "A" Control Circuit Signal Cycle Invalid  


DESCRIPTION

Refer to DTC P323A19.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>P323A19

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Note
P30DF62 Backup Boost Converter Circuit Board(Thermistor) Signal Compare Failure The following conditions is met for 1 second or more (2 trip detection logic):
·

Difference in temperature between thermistor 1 and thermistor 2 of the engine stop and start ECU is 40°C (72°F) or higher.


·

Engine stop and start ECU

·

Wire harness or connector

·

Battery

·

BBC NO. 1 fuse

·

BBC NO. 2 fuse


Blinks SAE Code: P30DF
P30EF4B Backup Boost Converter Circuit Board Over Temperature The following condition is met for 1 second or more (2 trip detection logic):
·

Engine stop and start ECU thermistor temperature is 135°C (275°F) or higher.


·

Engine stop and start ECU

·

Wire harness or connector

·

Battery

·

BBC NO. 1 fuse

·

BBC NO. 2 fuse


Blinks SAE Code: P30EF
P323A00 Backup Boost Converter "A" The following conditions is met for 1 second or more (1 trip detection logic):
·

Backup boost converter malfunction is detected.


·

Engine stop and start ECU

·

Wire harness or connector

·

Battery

·

BBC NO. 1 fuse

·

BBC NO. 2 fuse


Blinks SAE Code: P323A
P323A16 Backup Boost Converter "A" Circuit Voltage Below Threshold One of the following conditions is met for 2 second or more (2 trip detection logic):
·

B41 or IG41 voltage is 6.0 V or less and backup boost converter output overcurrent is not detected.

·

B42 or B43 voltage is 6.0 V or less, backup boost converter is not overheating and backup boost converter output overcurrent is not detected.


·

Engine stop and start ECU

·

Wire harness or connector

·

Battery

·

BBC NO. 1 fuse

·

BBC NO. 2 fuse


Blinks SAE Code: P323A
P323AA2 Backup Boost Converter "A" System Voltage Low The following conditions is met for 1 second or more (1 trip detection logic):
·

Backup boost converter malfunction is detected.


·

Engine stop and start ECU

·

Wire harness or connector

·

Battery

·

BBC NO. 1 fuse

·

BBC NO. 2 fuse


Blinks SAE Code: P323A
P323B29 Backup Boost Converter "A" Control Circuit Signal Invalid The following conditions is met for 1 second or more (1 trip detection logic):
·

Backup boost converter malfunction is detected.


·

Engine stop and start ECU

·

Wire harness or connector

·

Battery

·

BBC NO. 1 fuse

·

BBC NO. 2 fuse


Blinks SAE Code: P323C
P323B38 Backup Boost Converter "A" Control Circuit Signal Cycle Invalid The following conditions is met for 1 second or more (1 trip detection logic):
·

Backup boost converter malfunction is detected.


·

Engine stop and start ECU

·

Wire harness or connector

·

Battery

·

BBC NO. 1 fuse

·

BBC NO. 2 fuse


Blinks SAE Code: P323C

CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 392

b.

Start the engine and warm it up.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Depress the brake pedal and stop the vehicle.


e.

Keep the engine stopped by stop and start control for 1 second or more. (Keep the shift lever in D.)


f.

Release the brake pedal with the shift lever in D to start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.



g.

Check that DTCs are not output.

Powertrain > Stop and Start > Trouble Codes
50001 392


STOP AND START SYSTEM OPERATION CHECK


Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>OPERATION CHECK


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations, total number of engine starts and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BBC NO. 1, BBC NO. 2 FUSES)
a.

Disconnect the engine stop and start ECU connector.


b.

Remove the BBC NO. 1 and BBC NO. 2 fuses from the NO. 2 engine room relay block and junction block assembly


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B37)Location & Routing

Click Connector(B37)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

B37-1 (BIN2) - BBC NO. 2 fuse terminal 2 Always Below 1 Ω
B37-3 (BIN1) - BBC NO. 1 fuse terminal 2 Always Below 1 Ω
B37-1 (BIN2) - Body ground Always 10 kΩ or higher
B37-3 (BIN1) - Body ground Always 10 kΩ or higher
BBC NO. 2 fuse terminal 2 - Body ground Always 10 kΩ or higher
BBC NO. 1 fuse terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU POWER SOURCE CIRCUIT)
a.

Disconnect the engine stop and start ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B37)Location & Routing

Click Connector(B37)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

B37-1 (BIN2) - Body ground Always 9.5 to 14 V
B37-3 (BIN1) - Body ground Always 9.5 to 14 V



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I57)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

I57-18 (IGP) - Body ground Ignition switch ON 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)
a.

Disconnect the engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B37,B38)Location & Routing

Click Connector(B37)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

B37-2 (GND2) - Body ground Always Below 1 Ω
B37-8 (GND1) - Body ground Always Below 1 Ω
B38-6 (DGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the tire pressure warning ECU and receiver connector.


c.

Disconnect the integration control sub-assembly connector.


d.

Disconnect the meter mirror sub-assembly connector.


e.

Disconnect the No. 2 air conditioning control assembly connector.


f.

Disconnect the clearance warning ECU assembly connector.


g.

Disconnect the air conditioning control assembly connector.


h.

Disconnect the millimeter wave rader sensor assembly connector.


i.

Disconnect the No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


j.

Disconnect the radio receiver assembly connector.


k.

Disconnect the multi-display connector.


l.

Disconnect the navigation ECU connector.


m.

Disconnect the No. 1 interior illumination light assembly (for driver side) connector.


n.

Disconnect the No. 1 interior illumination light assembly (for front passenger side) connector.


o.

Disconnect the No. 1 interior illumination light assembly LH connector.


p.

Disconnect the No. 1 interior illumination light assembly RH connector.


q.

Disconnect the rear door inside handle illumination light switch LH connector.


r.

Disconnect the rear door inside handle illumination light switch RH connector.


s.

Disconnect the front door inside handle illumination light switch LH connector.


t.

Disconnect the front door inside handle illumination light switch RH connector.


u.

Disconnect the vanity light assembly LH connector.


v.

Disconnect the vanity light assembly RH connector.


w.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*1: for 12.3 Inch Display

*2: w/ Headup Display System

*3: w/ Pre-collision System

*4: w/ Rear Heater

*5: except 14 speaker

*6: for 14 speaker

*7: for Bulb type

*8: for LED type

Click Location & Routing(I57,T21,I22,I17,A10,Q52,I58,I78,B19,I8,I10,I18,I21,I61,I62,i6,h11,P5,O5,N8,M10,d5,d9,d4,d8)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(T21)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Electrical Key & Tire Pressure Monitoring System Receiver Assembly

Click Connector(I22)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Integration Control Sub-Assembly

Click Connector(I17)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Meter Mirror Sub-Assembly

Click Connector(A10)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Millimeter Wave Radar Sensor Assembly

Click Connector(Q52)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooler Control Switch Assembly

Click Connector(I58)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Clearance Warning ECU Assembly

Click Connector(I78)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Control Assembly

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

Click Connector(I8)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(I10)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(I18)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multi-Display Assembly

Click Connector(I21)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Navigation ECU Assembly

Click Connector(I61)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Foot Light RH (No. 1 Interior Illumination Light Assembly)

Click Connector(I62)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Foot Light LH (No. 1 Interior Illumination Light Assembly)

Click Connector(i6)Seat>Front Seat Wire LH>Foot Light LH (No. 1 Interior Illumination Light Assembly LH)

Click Connector(h11)Seat>Front Seat Wire RH>Foot Light RH (No. 1 Interior Illumination Light Assembly RH)

Click Connector(P5)Body>No. 2 Rear Door Wire>Rear Door Inside Handle Illumination Light Assembly LH

Click Connector(O5)Body>No. 1 Rear Door Wire>Rear Door Inside Handle Illumination Light Assembly RH

Click Connector(N8)Body>Front Door Wire LH>Front Door Inside Handle Illumination Light Assembly LH

Click Connector(M10)Body>Front Door Wire RH>Front Door Inside Handle Illumination Light Assembly RH

Click Connector(d5)Body>No. 1 Roof Wire>Vanity Light Assembly LH

Click Connector(d9)Body>No. 1 Roof Wire>Vanity Light Assembly LH

Click Connector(d4)Body>No. 1 Roof Wire>Vanity Light Assembly RH

Click Connector(d8)Body>No. 1 Roof Wire>Vanity Light Assembly RH

I57-3 (IG41) - T21-1 (IG) Always Below 1 Ω
I57-3 (IG41) - I22-4 (IG+)*1 Always Below 1 Ω
I57-3 (IG41) - I17-1 (IG)*2 Always Below 1 Ω
I57-3 (IG41) - A10-8 (IGB)*3 Always Below 1 Ω
I57-3 (IG41) - Q52-10 (IG)*4 Always Below 1 Ω
I57-3 (IG41) - I58-1 (IG) Always Below 1 Ω
I57-3 (IG41) - I78-8 (IG+) Always Below 1 Ω
I57-2 (B41) - T21-7 (+B) Always Below 1 Ω
I57-2 (B41) - B19-14 (+BI1) Always Below 1 Ω
I57-12 (B42) - I8-4 (+B1)*5 Always Below 1 Ω
I57-12 (B42) - I10-4 (+B1)*6 Always Below 1 Ω
I57-11 (B43) - I18-12 (B)*1 Always Below 1 Ω
I57-11 (B43) - I21-10 (+B) Always Below 1 Ω
I57-11 (B43) - I17-2 (B)*2 Always Below 1 Ω
I57-11 (B43) - I78-16 (+B) Always Below 1 Ω
I57-11 (B43) - I22-1 (B)*1 Always Below 1 Ω
I57-11 (B43) - I61-2 (B) Always Below 1 Ω
I57-11 (B43) - I62-2 (B) Always Below 1 Ω
I57-11 (B43) - i6-2 Always Below 1 Ω
I57-11 (B43) - h11-2 Always Below 1 Ω
I57-11 (B43) - P5-2 (+) Always Below 1 Ω
I57-11 (B43) - O5-2 (+) Always Below 1 Ω
I57-11 (B43) - N8-2 (+) Always Below 1 Ω
I57-11 (B43) - M10-2 (+) Always Below 1 Ω
I57-11 (B43) - d5-1 (B)*7 Always Below 1 Ω
I57-11 (B43) - d9-2 (B)*8 Always Below 1 Ω
I57-11 (B43) - d4-1 (B)*7 Always Below 1 Ω
I57-11 (B43) - d8-2 (B)*8 Always Below 1 Ω
I57-3 (IG41) - Body ground Always 10 kΩ or higher
I57-2 (B41) - Body ground Always 10 kΩ or higher
I57-12 (B42) - Body ground Always 10 kΩ or higher
I57-11 (B43) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR