Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2022.11
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467519 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Headlight ECU LH Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Headlight ECU LH Communication Stop Mode Communication stop for "Headlight Control" is indicated on the "Communication Bus Check" screen of the GTS.
(Click here)
·

Headlight ECU sub-assembly LH branch wire or connector

·

Power source circuit of headlight ECU sub-assembly LH

·

Headlight ECU sub-assembly LH ground circuit

·

Headlight ECU sub-assembly LH



WIRING DIAGRAM

C498935E02
0.469,2.115 2.135,2.469 1.667,0.354 10 false No. 6 Global CAN Junction Connector 0.479,1.948 2.083,2.156 1.604,0.208 10 false I182*1, I177*2 1.719,1.469 2.115,1.677 0.396,0.208 10 false 18 1.719,0.885 2.115,1.094 0.396,0.208 10 false 7 5.323,0.865 5.719,1.073 0.396,0.208 10 false 24 5.323,1.427 5.719,1.635 0.396,0.208 10 false 23 5.688,1 6.083,1.208 0.396,0.208 10 false CANH 5.688,1.583 6.083,1.792 0.396,0.208 10 false CANL 5.323,2.354 5.719,2.563 0.396,0.208 10 false 13 5.688,2.49 6.083,2.698 0.396,0.208 10 false ECUB 5.385,3.177 5.781,3.385 0.396,0.208 10 false 6 5.677,3.313 6.073,3.521 0.396,0.208 10 false IGR 5.344,4 5.74,4.208 0.396,0.208 10 false 12 5.677,4.135 6.073,4.344 0.396,0.208 10 false GND 5.229,4.771 6.146,5 0.917,0.229 10 false B4*1, B88*2 5.219,4.958 7.042,5.563 1.823,0.604 10 false Headlight ECU Sub-assembly LH 3.906,3.146 5.135,3.406 1.229,0.26 10 false ECU-IGR NO.3 1.813,2.479 3.5,2.948 1.688,0.469 10 false from H-LP LH Relay 1.76,3.313 3.271,3.698 1.51,0.385 10 false from IGR-NO.1 Relay 0.396,4.125 2.083,4.323 1.688,0.198 10 false *1: for LHD 0.396,4.521 2.083,4.719 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>PRECAUTION



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (HEADLIGHT ECU SUB-ASSEMBLY LH BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the B4*1 or B88*2 headlight ECU sub-assembly LH connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(B4)Location & Routing

Click Connector(B4)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

B4-24 (CANH) - B4-23 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(B88)Location & Routing

Click Connector(B88)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

B88-24 (CANH) - B88-23 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(B4)Location & Routing

Click Connector(B4)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

B4-12 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(B88)Location & Routing

Click Connector(B88)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

B88-12 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B4)Location & Routing

Click Connector(B4)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

B4-6 (IGR) - Body ground Ignition switch ON 11 to 14 V

for RHD
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B88)Location & Routing

Click Connector(B88)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

B88-6 (IGR) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(B4)Location & Routing

Click Connector(B4)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

B4-13 (ECUB) - Body ground For approximately 15 seconds after the ignition switch is turned to ON or off 11 to 14 V
Approximately 15 seconds elapsed after turning the ignition switch off Below 1 V

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(B88)Location & Routing

Click Connector(B88)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

B88-13 (ECUB) - Body ground For approximately 15 seconds after the ignition switch is turned to ON or off 11 to 14 V
Approximately 15 seconds elapsed after turning the ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG