The forward recognition camera controls the flow of current to the forward recognition with heater hood sub-assembly.
If the forward recognition camera detects a malfunction in the forward recognition with heater hood sub-assembly circuit, it will store this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C1AAE00 | Front Recognition Camera Heater Malfunction |
Either of the following conditions is met after 10 seconds have elapsed since the ignition switch was turned to ON:
·
Short to +B detected in the forward recognition with heater hood sub-assembly circuit for 1 second or more cumulatively
·
Open or short to ground detected in the forward recognition with heater hood sub-assembly circuit for 5 seconds or more |
·
Forward recognition with heater hood sub-assembly
·
Forward recognition camera
·
Harness or connector |
Front Recognition Camera | A |
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
When the forward recognition camera is replaced with a new one, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history (RoB) for each system.
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)
Sequential Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)
Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>DRIVING ADJUSTMENT
Pre-procedure1
Clear the DTCs.
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
Turn the ignition switch off.
| *a | Component without harness connected (Forward Recognition with Heater Hood Sub-assembly) |
Disconnect the d21 forward recognition with heater hood sub-assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (IG1) - 2 (HTR) | Always | 28.5 to 31.5 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(d21)Location & Routingewd_type=routing;type=c;code=d21 Click Connector(d21)Body>No. 1 Roof Wire>Forward Recognition with Heater Hood Sub-Assemblyewd_type=component;type=c;code=d21;pinno=1 |
||
| d21-1 (IG1) - Body ground | Ignition switch ON | 8 to 16 V |
| Ignition switch off | Below 1.5 V | |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the d33 forward recognition camera connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(d21,d33)Location & Routingewd_type=routing;type=c,c;code=d21,d33 Click Connector(d21)Body>No. 1 Roof Wire>Forward Recognition with Heater Hood Sub-Assemblyewd_type=component;type=c;code=d21;pinno=2 Click Connector(d33)Body>No. 1 Roof Wire>Forward Recognition Cameraewd_type=component;type=c;code=d33;pinno=1 |
||
| d21-2 (HTR) - d33-1 (HTR) | Always | Below 1 Ω |
| d21-2 (HTR) or d33-1 (HTR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG