Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Injector Circuit  


DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM

A221919E02
5.531,0.281 5.813,0.438 0.281,0.156 10 false #10 5.531,0.969 5.813,1.125 0.281,0.156 10 false #20 5.531,1.688 5.813,1.844 0.281,0.156 10 false #30 5.531,2.354 5.813,2.51 0.281,0.156 10 false #40 5.531,3.083 5.813,3.24 0.281,0.156 10 false #50 5.531,3.771 5.813,3.927 0.281,0.156 10 false #60 5.521,4.229 5.823,4.385 0.302,0.156 10 false E01 5.521,4.646 5.823,4.802 0.302,0.156 10 false E02 6.094,5.417 6.469,5.573 0.375,0.156 10 false ECM 5.26,4.656 5.448,4.802 0.188,0.146 10 false 21 5.26,4.208 5.448,4.354 0.188,0.146 10 false 22 5.26,3.771 5.458,3.917 0.198,0.146 10 false 83 5.26,3.073 5.438,3.229 0.177,0.156 10 false 43 5.26,2.375 5.458,2.521 0.198,0.146 10 false 84 5.26,1.688 5.448,1.833 0.188,0.146 10 false 44 5.26,0.99 5.469,1.135 0.208,0.146 10 false 85 5.26,0.292 5.438,0.438 0.177,0.146 10 false 45 6.094,5.25 6.406,5.396 0.313,0.146 10 false C39 3.479,0.281 3.594,0.438 0.115,0.156 10 false 1 3.479,0.979 3.594,1.135 0.115,0.156 10 false 1 3.479,1.688 3.594,1.844 0.115,0.156 10 false 1 3.479,2.354 3.594,2.51 0.115,0.156 10 false 1 3.479,3.073 3.594,3.229 0.115,0.156 10 false 1 3.479,3.771 3.594,3.927 0.115,0.156 10 false 1 4.104,0.281 4.219,0.438 0.115,0.156 10 false 2 4.104,0.979 4.219,1.135 0.115,0.156 10 false 2 4.104,1.688 4.219,1.844 0.115,0.156 10 false 2 4.104,2.354 4.219,2.51 0.115,0.156 10 false 2 4.104,3.073 4.219,3.229 0.115,0.156 10 false 2 4.104,3.76 4.219,3.917 0.115,0.156 10 false 2 3.229,0.635 4.542,0.813 1.313,0.177 10 false No. 1 Fuel Injector 3.229,0.5 3.5,0.646 0.271,0.146 10 false C8 3.229,1.896 3.5,2.042 0.271,0.146 10 false C9 3.229,3.25 3.5,3.396 0.271,0.146 10 false C11 3.229,1.354 4.448,1.531 1.219,0.177 10 false No. 2 Fuel Injector 3.229,1.219 3.531,1.365 0.302,0.146 10 false C20 3.229,3.969 3.531,4.115 0.302,0.146 10 false C16 3.229,2.042 4.51,2.219 1.281,0.177 10 false No. 3 Fuel Injector 3.229,2.74 4.51,2.917 1.281,0.177 10 false No. 4 Fuel Injector 3.229,2.594 3.531,2.771 0.302,0.177 10 false C25 3.229,3.385 4.573,3.563 1.344,0.177 10 false No. 5 Fuel Injector 3.229,4.104 4.51,4.281 1.281,0.177 10 false No. 6 Fuel Injector 1.073,1.292 1.323,1.458 0.25,0.167 10 false L21 1.531,0.542 1.781,0.708 0.25,0.167 10 false INJ 0.625,1.219 0.906,1.375 0.281,0.156 10 false IG2 0.625,3.521 1.271,3.688 0.646,0.167 10 false FL MAIN 0.625,2.729 0.958,2.896 0.333,0.167 10 false AM2 0.615,1.708 0.948,1.875 0.333,0.167 10 false AM2 1.052,1.469 1.99,1.948 0.938,0.479 10 false Ignition Switch Assembly 0.813,4.719 1.292,4.906 0.479,0.188 10 false Battery 0.625,1.969 0.74,2.125 0.115,0.156 10 false 5 0.625,0.979 0.74,1.135 0.115,0.156 10 false 6

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)
A167963C03
0.115,1.51 0.458,1.74 0.344,0.229 0.115,1.844 0.458,2.073 0.344,0.229 0.115,2.177 0.458,2.406 0.344,0.229 0.552,1.51 0.896,1.74 0.344,0.229 0.552,1.844 0.896,2.073 0.344,0.229 0.552,2.177 0.896,2.406 0.344,0.229 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 0.198,1.552 0.604,1.75 0.406,0.198 10 false C8 0.198,1.885 0.604,2.083 0.406,0.198 10 false C9 0.208,2.208 0.521,2.396 0.313,0.188 10 false C11 0.635,1.552 0.958,1.781 0.323,0.229 10 false C16 0.635,1.885 1.042,2.083 0.406,0.198 10 false C20 0.635,2.219 1.042,2.417 0.406,0.198 10 false C25
*a Front view of wire harness connector
(to Fuel Injector Assembly)


a.

Disconnect the fuel injector assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C8-1 - Body ground Ignition switch ON 11 to 14 V
C20-1 - Body ground Ignition switch ON 11 to 14 V
C9-1 - Body ground Ignition switch ON 11 to 14 V
C25-1 - Body ground Ignition switch ON 11 to 14 V
C11-1 - Body ground Ignition switch ON 11 to 14 V
C16-1 - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the fuel injector assembly connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT FUEL INJECTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - FUEL INJECTOR ASSEMBLY)

2.INSPECT FUEL INJECTOR ASSEMBLY
a.

Inspect the fuel injector assembly.

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)

NG

REPLACE FUEL INJECTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
a.

Disconnect the fuel injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C8-2 - C39-45 (#10) Always Below 1 Ω
C20-2 - C39-85 (#20) Always Below 1 Ω
C9-2 - C39-44 (#30) Always Below 1 Ω
C25-2 - C39-84 (#40) Always Below 1 Ω
C11-2 - C39-43 (#50) Always Below 1 Ω
C16-2 - C39-83 (#60) Always Below 1 Ω
C8-2 or C39-45 (#10) - Body ground Always 10 kΩ or higher
C20-2 or C39-85 (#20) - Body ground Always 10 kΩ or higher
C9-2 or C39-44 (#30) - Body ground Always 10 kΩ or higher
C25-2 or C39-84 (#40) - Body ground Always 10 kΩ or higher
C11-2 or C39-43 (#50) - Body ground Always 10 kΩ or higher
C16-2 or C39-83 (#60) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR