Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0660  Intake Manifold Tuning Valve Control Circuit / Open (Bank 1)  


DESCRIPTION

This circuit opens and closes the Intake Air Control Valve (IACV) in response to changes in the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).

When the engine speed is between 2200 rpm and 4100 rpm and the throttle valve opening angle is 60° or more, the ECM supplies current to the VSV (ON status), to close the IACV. Under other conditions, the VSV is usually OFF and the IACV is open.

A115903E03
0.878,0.354 1.034,0.535 0.156,0.181 10 6 1.238,0.354 1.394,0.535 0.156,0.181 10 4 1.598,0.354 1.754,0.535 0.156,0.181 10 2 0.878,1.828 1.034,2.009 0.156,0.181 10 5 1.238,1.828 1.394,2.009 0.156,0.181 10 3 1.598,1.828 1.754,2.009 0.156,0.181 10 1 0.103,0.719 0.516,0.889 0.413,0.170 10 IACV 0.53,0.834 0.926,1.141 false 2.472,1.591 3.409,1.760 0.937,0.170 10 Throttle Valve 5.613,0.248 7.161,0.418 1.548,0.170 10 Valve Closed (VSV: ON) 4.249,0.43 5.186,0.759 0.937,0.330 10 Throttle Valve Opening Angle 5.602,2.336 6.883,2.514 1.281,0.178 10 Engine Speed (rpm) 5.182,2.076 5.624,2.246 0.442,0.170 10 2200 2.763,1.181 2.802,1.57 false 4.909,1.036 5.136,1.217 0.227,0.181 10 60° 5.585,0.351 5.425,0.601 false 6.05,2.083 6.448,2.238 0.398,0.155 10 4100

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1) Conditions (a) and (b) are met for 0.5 sec. or more (2 trip detection logic):
(a) The voltage of terminal ACIS of the ECM is low when the VSV is OFF.
(b) The engine has started.
·

Open or short in VSV for ACIS circuit

·

VSV for ACIS

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A161384E06
0.646,1.281 1.615,1.604 0.969,0.323 10 false from EFI MAIN Relay 2.25,1.458 2.938,1.625 0.688,0.167 10 false EFI NO. 2 3.656,1.208 3.771,1.417 0.115,0.208 10 false 1 4.417,1.208 4.531,1.417 0.115,0.208 10 false 2 5.219,1.208 5.49,1.417 0.271,0.208 10 false 107 5.552,1.208 5.917,1.417 0.365,0.208 10 false ACIS 3.677,1.583 4,1.75 0.323,0.167 10 false C37 3.677,1.76 4.563,1.927 0.885,0.167 10 false VSV for ACIS 5.719,3.042 6.104,3.219 0.385,0.177 10 false C39 5.719,3.177 6.104,3.333 0.385,0.156 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR INTAKE CONTROL)
a.
A233358C03
2.646,1.625 2.417,1.625 2.417,1.625 2.219,1.208 false 2.458,3.76 2.229,3.76 2.229,3.76 2.031,3.344 false 1.177,0.979 1.427,1.177 false 0.854,1.24 1.26,1.427 false 0.896,3.177 1.24,3.292 false 0.729,3.427 1.073,3.563 false 0.24,0.26 0.469,0.479 0.229,0.219 10 *a 0.302,2.646 0.521,2.823 0.219,0.177 10 *b 1.031,0.875 1.208,1.083 0.177,0.208 10 *2 0.75,3.083 1.01,3.292 0.26,0.208 10 *2 0.708,1.156 0.969,1.344 0.26,0.188 10 *1 0.563,3.333 0.719,3.531 0.156,0.198 10 *1 1.021,0.469 1.229,0.677 0.208,0.208 10 *c 0.542,1.594 0.75,1.771 0.208,0.177 10 *c 1.146,2.615 1.354,2.823 0.208,0.208 10 *c 2.594,2.979 2.802,3.188 0.208,0.208 10 *c 2.688,1.542 2.948,1.729 0.26,0.188 10 *3 2.51,3.667 2.771,3.854 0.26,0.188 10 *3
*1 Port F
*2 Port E
*3 Air Filter
*a VSV for ACIS is ON
*b VSV for ACIS is OFF
*c Air


Disconnect the vacuum hose from port F of the VSV for ACIS.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Intake Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Intake Control
50004 234 3

f.

Operate the VSV for ACIS.


g.

Check the VSV for ACIS air flow when switching the VSV for ACIS..

OK:
Activate the VSV for Intake Control Specified Condition
ON Air from port E flows out through port F
OFF Air from port E flows out through air filter


Result:
Proceed to
OK
NG




OK

2.INSPECT VACUUM SWITCHING VALVE ASSEMBLY (FOR ACIS)

NG

5.CHECK VACUUM HOSE
2.INSPECT VACUUM SWITCHING VALVE ASSEMBLY (FOR ACIS)
a.

Inspect the vacuum switching valve (for ACIS).

Click hereEngine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE (FOR ACIS))

NG

REPLACE VACUUM SWITCHING VALVE (FOR ACIS)

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE (FOR ACIS))
a.
A225830C32
0.302,1.063 0.698,1.354 0.396,0.292 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 0.375,1.135 0.833,1.333 0.458,0.198 10 false C37
*a Front view of wire harness connector
(to Vacuum Switching Valve Assembly (for ACIS))


Disconnect the vacuum switching valve (for ACIS) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C37-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR ACIS) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (VACUUM SWITCHING VALVE (FOR ACIS) - EFI-MAIN NO.1 RELAY)

4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR ACIS) - ECM)
a.

Disconnect the vacuum switching valve (for ACIS) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C37-2 - C39-107 (ACIS) Always Below 1 Ω
C37-2 or C39-107 (ACIS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK VACUUM HOSE

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

5.CHECK VACUUM HOSE
a.

Check that the vacuum hose is connected correctly, and that there are no cracks, holes, damage, or looseness.

OK:

Vacuum hose is nomal.



Result:
Proceed to
OK
NG



OK

6.INSPECT INTAKE AIR SURGE TANK (INTAKE AIR CONTROL VALVE)

NG

REPAIR OR REPLACE VACUUM HOSE

6.INSPECT INTAKE AIR SURGE TANK (INTAKE AIR CONTROL VALVE)
a.

Inspect the intake air control valve.

Click hereEngine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

NG

REPLACE INTAKE AIR SURGE TANK (INTAKE AIR CONTROL VALVE)