Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0327  Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)  P0328  Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)  P0332  Knock Sensor 2 Circuit Low Input (Bank 2)  P0333  Knock Sensor 2 Circuit High Input (Bank 2)  


DESCRIPTION

Flat type knock sensors (non-resonant type) have structures that can detect vibrations between approximately 5 kHz and 15 kHz.

A knock sensor is fitted onto the engine block to detect engine knocking.

The knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) The output voltage of the knock sensor (bank 1) is below 0.5 V (1 trip detection logic).
·

Short in knock sensor (bank 1) circuit

·

Knock sensor (bank 1)

·

ECM


Comes on DTC stored
P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor) The output voltage of the knock sensor (bank 1) is higher than 4.5 V (1 trip detection logic).
·

Open in knock sensor (bank 1) circuit

·

Knock sensor (bank 1)

·

ECM


Comes on DTC stored
P0332 Knock Sensor 2 Circuit Low Input (Bank 2) The output voltage of the knock sensor (bank 2) is below 0.5 V (1 trip detection logic).
·

Short in knock sensor (bank 2) circuit

·

Knock sensor (bank 2)

·

ECM


Comes on DTC stored
P0333 Knock Sensor 2 Circuit High Input (Bank 2) The output voltage of the knock sensor (bank 2) is higher than 4.5 V (1 trip detection logic).
·

Open in knock sensor (bank 2) circuit

·

Knock sensor (bank 2)

·

ECM


Comes on DTC stored

HINT:

When any of DTCs P0327, P0328, P0332 and P0333 are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.


Reference: Inspection using an oscilloscope

A185975E04
0.344,0.323 1.865,0.51 1.521,0.188 10 false KNK1 Signal Waveform 2.552,0.781 3.115,0.969 0.563,0.188 10 false 1 V/DIV. 2.656,1.677 3.021,1.854 0.365,0.177 10 false GND 0.406,2.531 1.229,2.719 0.823,0.188 10 false 1 msec./DIV.

The correct waveform is as shown.

Item Content
Terminal KNK1 - EKNK
KNK2 - EKN2
Equipment Setting 1 V/DIV.
1 msec./DIV.
Condition Engine speed maintained at 4000 rpm with warm engine

MONITOR DESCRIPTION

If the output voltage transmitted by the knock sensor remains low or high for more than 1 second, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.

The monitor for DTCs P0327, P0328, P0332 and P0333 begins to run when 5 seconds have elapsed since the engine was started.

If the malfunction is not repaired successfully, DTC P0327, P0328, P0332 or P0333 is stored 5 seconds after the engine is next started.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and wait 5 minutes.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0327, P0328, P0332 or P0333.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.




WIRING DIAGRAM

A225321E07
0.552,1.667 0.781,1.865 0.229,0.198 10 false h2 0.552,1.823 2.323,2.021 1.771,0.198 10 false Knock Sensor (for Bank 1) 0.719,1.198 0.906,1.427 0.188,0.229 10 false 1 1.865,1.198 2.052,1.427 0.188,0.229 10 false 2 0.552,4.052 0.781,4.25 0.229,0.198 10 false h1 0.552,4.219 2.354,4.417 1.802,0.198 10 false Knock Sensor (for Bank 2) 0.719,3.583 0.906,3.813 0.188,0.229 10 false 1 1.865,3.583 2.052,3.813 0.188,0.229 10 false 2 2.26,2.563 2.854,2.76 0.594,0.198 10 false Shielded 2.26,4.948 2.854,5.146 0.594,0.198 10 false Shielded 3.417,1.115 3.594,1.292 0.177,0.177 10 false 2 3.313,1.323 3.635,1.49 0.323,0.167 10 false Ch1 3.417,1.917 3.594,2.094 0.177,0.177 10 false 5 3.313,2.104 3.635,2.271 0.323,0.167 10 false Ch1 3.417,2.708 3.594,2.885 0.177,0.177 10 false 1 3.313,2.896 3.635,3.063 0.323,0.167 10 false Ch1 3.417,3.5 3.594,3.677 0.177,0.177 10 false 4 3.313,3.688 3.635,3.854 0.323,0.167 10 false Ch1 3.417,4.302 3.594,4.479 0.177,0.177 10 false 6 3.302,4.479 3.625,4.646 0.323,0.167 10 false Ch1 4.604,2.563 5.208,2.729 0.604,0.167 10 false Shielded 4.604,4.948 5.208,5.115 0.604,0.167 10 false Shielded 5.854,1.208 6.26,1.375 0.406,0.167 10 false KNK1 5.583,1.208 5.792,1.375 0.208,0.167 10 false 95 5.854,2.01 6.26,2.177 0.406,0.167 10 false EKNK 5.583,2.01 5.771,2.177 0.188,0.167 10 false 94 5.854,3.604 6.26,3.771 0.406,0.167 10 false KNK2 5.49,3.604 5.833,3.771 0.344,0.167 10 false 118 5.854,4.406 6.26,4.573 0.406,0.167 10 false ENK2 5.458,4.406 5.771,4.573 0.313,0.167 10 false 117 5.885,5.396 6.292,5.563 0.406,0.167 10 false C39 5.885,5.531 6.281,5.698 0.396,0.167 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

DTCs P0327 and P0328 are for the bank 1 knock sensor circuit.

·

DTCs P0332 and P0333 are for the bank 2 knock sensor circuit.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ DTC OUTPUT (CHECK KNOCK SENSOR CIRCUIT)
A294700C05
1.417,0.396 1.75,0.615 0.333,0.219 10 false Ch1 1.479,2.865 1.813,3.073 0.333,0.208 10 false Ch1 2.865,0.438 3.177,0.635 0.313,0.198 10 false *2 0.271,0.698 0.583,0.896 0.313,0.198 10 false *1 0.302,1.188 0.458,1.385 0.156,0.198 10 false 1 0.646,1.188 0.802,1.385 0.156,0.198 10 false 2 0.292,2.042 0.448,2.24 0.156,0.198 10 false 1 0.656,2.042 0.813,2.24 0.156,0.198 10 false 2 1.177,1.01 1.333,1.208 0.156,0.198 10 false 2 1.177,1.396 1.333,1.594 0.156,0.198 10 false 5 1.177,2.177 1.333,2.375 0.156,0.198 10 false 6 1.177,1.792 1.333,1.99 0.156,0.198 10 false 4 1.844,1.01 2,1.208 0.156,0.198 10 false 2 1.844,1.396 2,1.594 0.156,0.198 10 false 5 1.854,1.781 2.01,1.979 0.156,0.198 10 false 4 1.844,2.167 2,2.365 0.156,0.198 10 false 6 2.417,1.104 2.615,1.323 0.198,0.219 10 false 95 2.417,1.5 2.604,1.708 0.188,0.208 10 false 94 2.344,1.885 2.635,2.094 0.292,0.208 10 false 118 2.344,2.281 2.646,2.5 0.302,0.219 10 false 117 0.417,3.167 0.729,3.365 0.313,0.198 10 false *a 2.688,3.167 3,3.365 0.313,0.198 10 false *b
*1 Knock Sensor
*2 ECM
*a Front view of wire harness connector
(to Knock Sensor Wire)
*b Front view of wire harness connector
(to ECM Wire)


a.

Disconnect the Ch1 connector.


b.

Using lead wires, connect the connectors as follows:

Male Connector - Female Connector
Terminal 2 - Terminal 4
Terminal 5 - Terminal 6
Terminal 4 - Terminal 2
Terminal 6 - Terminal 5


c.

Warm up the engine.


d.

Run the engine at 3000 rpm for 10 seconds or more.


e.

Connect the GTS to the DLC3.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

h.

Read the DTCs.

Result:
Result Proceed to
DTC is same as when vehicle was brought in
(for example, P0327 and P0328 are output again, or P0332 and P0333 are output again)
A
DTC is different from when vehicle was brought in
(for example, P0327 and P0328 are output at first, but then P0332 and P0333 are output, or vice versa)
B




A

2.CHECK HARNESS AND CONNECTOR (CONNECTOR - ECM)

B

4.INSPECT KNOCK SENSOR
2.CHECK HARNESS AND CONNECTOR (CONNECTOR - ECM)
a.

Disconnect the Ch1 connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Ch1 female connector 2 - C39-95 (KNK1) Always Below 1 Ω
Ch1 female connector 5 - C39-94 (EKNK) Always Below 1 Ω
Ch1 female connector 4 - C39-118 (KNK2) Always Below 1 Ω
Ch1 female connector 6 - C39-117 (EKN2) Always Below 1 Ω
Ch1 female connector 2 or C39-95 (KNK1) - Body ground Always 10 kΩ or higher
Ch1 female connector 5 or C39-94 (EKNK) - Body ground Always 10 kΩ or higher
Ch1 female connector 4 or C39-118 (KNK2) - Body ground Always 10 kΩ or higher
Ch1 female connector 6 or C39-117 (EKN2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VOLTAGE)
a.
A108338C05
0.5,0.99 0.865,1.26 0.365,0.271 0.188,0.125 0.5,0.323 0.313,0.198 10 false *a 0.552,1.042 0.896,1.24 0.344,0.198 10 false Ch1
*a Front view of wire harness connector
(to ECM Wire)


Disconnect the Ch1 connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Ch1 female connector 2 - 5 Ignition switch ON 4.5 to 5.5 V
Ch1 female connector 4 - 6 Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT KNOCK SENSOR
a.
A072922C04
0.49,0.875 0.844,1.135 0.354,0.26 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.542,0.917 0.896,1.135 0.354,0.219 10 false Ch1
*a Front view of wire harness connector
(to Knock Sensor Wire)


Disconnect the Ch1 connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Ch1 Male connector 2 - 5 20°C (68°F) 120 to 280 kΩ
Ch1 Male connector 4 - 6 20°C (68°F) 120 to 280 kΩ



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (CONNECTOR - KNOCK SENSOR)
5.CHECK HARNESS AND CONNECTOR (CONNECTOR - KNOCK SENSOR)
HINT:
·

If DTC P0327 or P0328 has changed to P0332 or P0333, check the knock sensor circuit of the right bank.

·

If DTC P0332 or P0333 has changed to P0327 or P0328, check the knock sensor circuit of the left bank.



a.

Disconnect the Ch1 connector.


b.

Disconnect the knock sensor (for bank 1) connectors.


c.

Disconnect the knock sensor (for bank 2) connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Ch1 male connector 2 - h2-2 Always Below 1 Ω
Ch1 male connector 5 - h2-1 Always Below 1 Ω
Ch1 male connector 4 - h1-2 Always Below 1 Ω
Ch1 male connector 6 - h1-1 Always Below 1 Ω
Ch1 male connector 2 or h2-2 - Body ground Always 10 kΩ or higher
Ch1 male connector 5 or h2-1 - Body ground Always 10 kΩ or higher
Ch1 male connector 4 or h1-2 - Body ground Always 10 kΩ or higher
Ch1 male connector 6 or h1-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR