Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor system consists of a crank angle sensor plate and a pickup coil.

The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection time and ignition timing are controlled.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0335 Crankshaft Position Sensor "A" Circuit One of the following conditions is met when VVT sensor circuit fail is not detected (1 trip detection logic):
·

No crankshaft position sensor signal is sent to the ECM while cranking

·

No crankshaft position sensor signal is sent to the ECM at an engine speed of 600 rpm or more

·

Missing crankshaft position sensor signal despite VVT sensor signal inputs normal after engine cranked


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft (crank angle sensor plate)

·

ECM


Comes on DTC stored
P0339 Crankshaft Position Sensor "A" Circuit Intermittent Under conditions (a), (b) and (c), no crankshaft position sensor signal is sent to the ECM for 0.05 seconds or more (1 trip detection logic):
(a) The engine speed is 1000 rpm or more.
(b) The starter signal is off.
(c) 3 seconds or more have elapsed since the starter signal switched from on to off.
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft (crank angle sensor plate)

·

ECM


- DTC stored

A122767E19
0.198,0.646 0.427,0.813 0.229,0.167 10 false NE 0.125,1.125 0.427,1.281 0.302,0.156 10 false VV1 0.125,1.51 0.427,1.656 0.302,0.146 10 false VV2 2.896,0.635 3.229,0.781 0.333,0.146 10 false GND 2.896,1.583 3.229,1.729 0.333,0.146 10 false GND 2.896,1.208 3.229,1.354 0.333,0.146 10 false GND 1.823,1.885 2.792,2.042 0.969,0.156 10 false 20 msec./DIV 2.75,0.344 3.26,0.5 0.51,0.156 10 false 5 V/DIV 0.042,0.021 2.365,0.208 2.323,0.188 10 false VV1, VV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope.

HINT:
·

The correct waveform is as shown.

·

VV1 and VV2 stand for the VVT sensor signal, and NE stands for the crankshaft position sensor signal.

·

Grounding failure of the shielded wire may cause noise in the waveforms.



Item Content
Terminal NE+ - NE-
VV1+ - VV1-
VV2+ - VV2-
Equipment Setting 5 V/DIV.,
20 msec./DIV.
Condition Idling


MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the engine running, the ECM interprets this as a malfunction of the sensor.

If the malfunction is not repaired successfully, a DTC is stored 20 seconds after the engine is next started.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 20 seconds or more [A].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0335 or P0339.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.




WIRING DIAGRAM

A160378E09
0.708,1.615 1.031,1.771 0.323,0.156 10 false C2 0.698,1.771 2.448,1.927 1.75,0.156 10 false Crankshaft Position Sensor 2.104,0.802 2.24,0.979 0.135,0.177 10 false 1 2.104,1.292 2.24,1.469 0.135,0.177 10 false 2 3.271,1.771 3.865,1.917 0.594,0.146 10 false Shielded 5.021,0.802 5.292,0.99 0.271,0.188 10 false 110 5.385,0.802 5.708,0.99 0.323,0.188 10 false NE+ 5.021,1.271 5.292,1.458 0.271,0.188 10 false 111 5.385,1.271 5.708,1.458 0.323,0.188 10 false NE- 5.552,2.021 5.865,2.188 0.313,0.167 10 false C39 5.552,2.167 5.938,2.333 0.385,0.167 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 is output again, check the following items related to the VVT sensor.

(a)

Installation condition of the VVT sensor.

(b)

Installation condition of the camshaft.

(c)

Connection of the VVT sensor connector.



·

If no problem is found through by this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.


·

Check the engine speed. The engine speed can be checked by using the GTS. To check, follow the operation below:

(a)

Connect the GTS to the DLC3.

(b)

Start the engine.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the Crankshaft Position (CKP) sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the CKP sensor output voltage is insufficient.


·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

e.

Start the engine.


f.

Read the values displayed on the GTS while the engineis running.

OK:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the GTS.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the GTS remains zero (0), there may be an open or short in the crankshaft position sensor circuit.




Result:
Proceed to
OK
NG



OK

NG

2.INSPECT CRANKSHAFT POSITION SENSOR
2.INSPECT CRANKSHAFT POSITION SENSOR

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C2-1 - C39-110 (NE+) Always Below 1 Ω
C2-2 - C39-111 (NE-) Always Below 1 Ω
C2-1 or C39-110 (NE+) - Body ground Always 10 kΩ or higher
C2-2 or C39-111 (NE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
a.
A295942E01
0.417,1.885 0.729,2.083 0.313,0.198 10 OK 2.667,1.885 2.979,2.083 0.313,0.198 10 NG 1.688,1.573 2.396,1.771 0.708,0.198 10 Clearance

Check the crankshaft position sensor installation condition.

OK:

Crankshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

5.INSPECT CRANKSHAFT (TEETH OF CRANK ANGLE SENSOR PLATE)

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

5.INSPECT CRANKSHAFT (TEETH OF CRANK ANGLE SENSOR PLATE)
a.

Check the teeth of the crank angle sensor plate.

OK:

Crank angle sensor plate does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

6.CHECK WHETHER DTC OUTPUT RECURS

NG

6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

i.

Read the DTCs.

Result:
Result Proceed to
No output A
P0335 or P0339 B


HINT:

If the engine does not start, replace the ECM.




A

END

B