Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2021.12
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  P0057  Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2)  P0058  Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2)  P102D  O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON  P105D  O2 Sensor Heater Circuit Performance Bank 2 Sensor 2 Stuck ON  


DESCRIPTION

Refer to DTC P0137.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0137

HINT:
·

Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.

·

When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The heated oxygen sensor sensor heater circuit uses a relay on the +B side of the circuit.

A287498E06
0.083,0.042 3.365,0.229 3.281,0.188 10 false Reference (System Diagram of Bank 1 Sensor 2) : 1.323,1.26 1.948,1.594 0.625,0.333 10 false EFI 2.104,2.385 2.75,2.563 0.646,0.177 10 false EFI MAIN 3.49,2.229 5.01,2.406 1.521,0.177 10 false Heated Oxygen Sensor 3.458,0.99 3.771,1.167 0.313,0.177 10 false +B 4.552,1 4.927,1.177 0.375,0.177 10 false HT1B 3.49,1.552 3.719,1.729 0.229,0.177 10 false E2 4.552,1.552 4.979,1.729 0.427,0.177 10 false OX1B 3.885,1.24 4.323,1.417 0.438,0.177 10 false Heater 3.875,1.885 4.333,2.063 0.458,0.177 10 false Sensor 5.823,3.469 6.146,3.646 0.323,0.177 10 false ECM 5.146,1 5.521,1.177 0.375,0.177 10 false HT1B 5.146,1.552 5.542,1.729 0.396,0.177 10 false OX1B 5.146,2.594 5.531,2.771 0.385,0.177 10 false EX1B 5.146,2.99 5.552,3.167 0.406,0.177 10 false MREL 0.156,1.073 0.927,1.24 0.771,0.167 10 false from Battery 2.917,1.26 3.552,1.438 0.635,0.177 10 false EFI NO. 2


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) The heater current is less than the specified value while the heater is operating.
(1 trip detection logic)
·

Open in heated oxygen sensor heater (bank 1 sensor 2) circuit

·

Heated oxygen sensor heater (bank 1 sensor 2)

·

EFI NO. 2 fuse

·

ECM


Comes on DTC stored
P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) The heater current is higher than the specified value while the heater is operating.
(1 trip detection logic)
·

Short in heated oxygen sensor heater (bank 1 sensor 2) circuit

·

Heated oxygen sensor heater (bank 1 sensor 2)

·

EFI NO. 2 fuse

·

ECM


Comes on DTC stored
P0057 Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2) The heater current is less than the specified value while the heater is operating.
(1 trip detection logic)
·

Open in heated oxygen sensor heater (bank 2 sensor 2) circuit

·

Heated oxygen sensor heater (bank 2 sensor 2)

·

EFI NO. 2 fuse

·

ECM


Comes on DTC stored
P0058 Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2) The heater current is higher than the specified value while the heater is operating.
(1 trip detection logic)
·

Short in heated oxygen sensor heater (bank 2 sensor 2) circuit

·

Heated oxygen sensor heater (bank 2 sensor 2)

·

EFI NO. 2 fuse

·

ECM


Comes on DTC stored
P102D O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON The heater current is higher than the specified value while the heater is not operating.
(1 trip detection logic)
ECM
Short in heated oxygen sensor heater (bank 1 sensor 2) circuit
Comes on DTC stored
P105D O2 Sensor Heater Circuit Performance Bank 2 Sensor 2 Stuck ON The heater current is higher than the specified value while the heater is not operating.
(1 trip detection logic)
ECM
Short in heated oxygen sensor heater (bank 2 sensor 2) circuit
Comes on DTC stored


MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions. If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor and stores a DTC.

CONFIRMATION DRIVING PATTERN

A198819E50
0.749,0.969 1.396,1.162 0.647,0.193 10 3000 rpm 0.969,1.739 1.376,1.9 0.406,0.161 10 Idling 0.417,2.006 1.346,2.345 0.929,0.339 10 Ignition Switch ON 1.926,2.132 2.161,2.297 0.235,0.166 10 [A] 2.762,1.623 2.956,1.816 0.193,0.193 10 [B] 4.026,0.868 4.284,1.006 0.258,0.138 10 [C] 5.39,1.6 5.614,1.782 0.223,0.182 10 [D] 2.272,2.589 3.465,2.746 1.193,0.156 10 5 minutes or more 4.873,2.608 6.067,2.764 1.193,0.156 10 5 minutes or more 3.85,2.617 4.423,2.783 0.573,0.166 10 1 minute 5.98,3.028 6.183,3.231 0.203,0.203 10 [E]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0037, P0038, P0057, P0058, P102D or P105D.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)
a.
A149595C32
1.802,0.865 2.219,1.115 0.417,0.25 0.948,0.865 1.365,1.115 0.417,0.25 1.948,1.833 2.365,1.417 false 0.083,0.083 0.344,0.281 0.26,0.198 10 false *a 1.885,0.917 2.198,1.125 0.313,0.208 10 false C17 2.417,1.333 2.667,1.5 0.25,0.167 10 false +B 1.021,0.917 1.333,1.125 0.313,0.208 10 false C18 1.427,0.813 1.74,1.021 0.313,0.208 10 false *A 2.281,0.813 2.594,1.021 0.313,0.208 10 false *B
*A Bank 1
*B Bank 2
*a Front view of wire harness connector
(to Heated Oxygen Sensor)


Disconnect the heated oxygen sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C18-2 (+B) - Body ground Ignition switch ON 11 to 14 V
C17-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (HEATED OXYGEN SENSOR - EFI MAIN RELAY)

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor (bank 1 sensor 2) connector.


b.

Disconnect the heated oxygen sensor (bank 2 sensor 2) connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C18-1 (HT1B) - C39-48 (HT1B) Always Below 1 Ω
C17-1 (HT2B) - C39-47 (HT2B) Always Below 1 Ω
C18-1 (HT1B) or C39-48 (HT1B) - Body ground Always 10 kΩ or higher
C17-1 (HT2B) or C39-47 (HT2B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR