Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › CRANKSHAFT POSITION SENSOR
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135355 CRANKSHAFT POSITION SENSOR A

1VD-FTV ENGINE CONTROL  CRANKSHAFT POSITION SENSOR  INSTALLATION  


PROCEDURE

Hide 11301K 1.INSTALL CRANKSHAFT POSITION SENSOR

a.

Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.

HINT:
·

When reusing the crankshaft position sensor, inspect the O-ring.

·

If the O-ring has scratches or cuts, replace the crankshaft position sensor.




b.

Install the crankshaft position sensor with the bolt to the timing chain cover sub-assembly.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Connect the crankshaft position sensor wire harness clamp.


d.

Connect the connector to the crankshaft position sensor.


Hide 2.CONNECT COOLER COMPRESSOR (w/ Air Conditioning System)

Hide 16630H 3.INSTALL IDLER PULLEY ASSEMBLY (w/o Air Conditioning System)

a.

Install the idler pulley assembly with the 3 bolts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 17875 4.INSTALL INTAKE AIR CONNECTOR PIPE

a.
A329068C01
2.219,0.25 2.323,0.25 2.323,0.25 2.458,0.479 true 0.469,4.458 0.542,4.458 0.542,4.458 0.667,4.198 true 0.448,0.073 0.667,0.271 0.219,0.198 10 false *d 2.854,0.188 3.073,0.365 0.219,0.177 10 false *a 2.833,3.417 3.052,3.604 0.219,0.188 10 false *c 1.073,3.917 1.302,4.083 0.229,0.167 10 false *b 1.958,0.156 2.302,0.365 0.344,0.208 10 false 90° 0.198,4.375 0.479,4.552 0.281,0.177 10 false 90°
*a Front Side
*b Left Side
*c 6.0 mm (0.236 in.) or less
*d 5.0 mm (0.197 in.) or less


Connect the intake air connector pipe to the No. 3 intake air connector pipe.

NOTICE:

Push on the intake air connector pipe to the No. 3 intake air connector pipe so that the clearance is 6.0 mm (0.236 in.) or less.



b.

Connect the intake air connector pipe to the intake air connector sub-assembly .

NOTICE:

Push on the intake air connector sub-assembly to the intake air connector pipe so that the clearance is 5.0 mm (0.197 in.) or less.



c.

Tighten the 2 hose clamps.

Torque:
4.8 N*m (49 kgf*cm, 42 in.*lbf)


d.

Install the intake air connector pipe with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.

Connect the ventilation hose to the intake air connector pipe, and slide the clip to secure the hose.


f.

Attach the wire harness clamp to connect the wire harness to the intake air connector pipe.


g.

Connect the engine coolant temperature sensor connector.


Hide 16361A 5.INSTALL FAN AND GENERATOR V BELT

Hide 53737B 6.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron seal LH with the 11 clips.