Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2014.08–2016.08
RM25T0E _51 Engine / Hybrid System _029207 1VD-FTV ENGINE MECHANICAL _0132955 ENGINE ASSEMBLY A

1VD-FTV ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 12371 1.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.

Install the rear No. 1 engine mounting insulator to the manual transmission with transfer with the 4 bolts.

Torque:
59 N*m (602 kgf*cm, 44 ft.*lbf)


Hide 12361 2.INSTALL FRONT ENGINE MOUNTING INSULATOR LH

a.

Install the engine mounting stabilizer and front engine mounting insulator LH with a new nut.

Torque:
71.5 N*m (729 kgf*cm, 53 ft.*lbf)


Hide 12361 3.INSTALL FRONT ENGINE MOUNTING INSULATOR RH

a.

Install the engine mounting stabilizer and front engine mounting insulator RH with a new nut.

Torque:
71.5 N*m (729 kgf*cm, 53 ft.*lbf)


Hide 5.REMOVE ENGINE STAND

a.

Attach an engine sling device and hang the engine assembly with a chain block.


b.

Lift the engine assembly, and remove it from the engine stand.


c.

Place the engine assembly onto a working bench.


Hide 13405 6.INSTALL FLYWHEEL SUB-ASSEMBLY

a.

Temporarily install the flywheel sub-assembly with 8 new bolts.

NOTICE:
·

Align the crankshaft knock pin and flywheel sub-assembly knock pin hole.

·

Do not strike or damage the flywheel sub-assembly installation bolts. Be sure to handle them carefully.

·

Make sure there is no oil on the bolts.




b.
A163869C01
0.5,4.333 0.5,3.792 true 0.75,2.125 0.75,1.583 true 1.25,3 1.917,3 true 1.958,4.146 1.958,3.604 true 1.104,2.906 1.417,3.063 0.313,0.156 10 false *1 1.875,4.125 2.188,4.281 0.313,0.156 10 false *a 0.615,2.135 1.073,2.333 0.458,0.198 10 false SST 0.365,4.344 0.823,4.542 0.458,0.198 10 false SST
*1 Crankshaft Pulley
*a Protective Tape


Using SST, hold the crankshaft pulley.

SST
09960-10010  (09962-01000, 09963-01000)

NOTICE:

To prevent damage to the crankshaft pulley, apply protective tape to the contact areas of SST and the crankshaft pulley before performing this procedure.



c.
A163846N01
1.313,1.271 1.438,1.448 0.125,0.177 10 true 6 1.979,1.521 2.156,1.688 0.177,0.167 10 true 8 2.135,0.958 2.292,1.135 0.156,0.177 10 true 5 1.573,0.75 1.75,0.906 0.177,0.156 10 true 7 2.156,1.26 2.333,1.427 0.177,0.167 10 true 4 1.313,1 1.438,1.177 0.125,0.177 10 true 3 1.917,0.75 2.073,0.917 0.156,0.167 10 true 1 1.583,1.552 1.771,1.771 0.188,0.219 10 true 2

Uniformly install and tighten the 8 bolts in the sequence shown in the illustration.

Torque:
182 N*m (1856 kgf*cm, 134 ft.*lbf)


Hide 31250 7.INSTALL CLUTCH DISC ASSEMBLY

Hide 31210 8.INSTALL CLUTCH COVER ASSEMBLY

Hide 9.INSTALL ENGINE ASSEMBLY

a.

Attach the engine sling device and hang the engine assembly with the chain block.


b.

Slowly lower the engine assembly into the engine compartment.


c.

Install 2 new plate washers and 2 new nuts to the front engine mounting insulator LH and RH.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)


Hide 37110 12.INSTALL REAR PROPELLER SHAFT ASSEMBLY

Hide 37140 13.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Hide 82112 14.INSTALL NO. 2 ENGINE ROOM WIRE

a.
A328673

Install the No. 2 engine room wire with the bolt.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)

HINT:

Make sure that the crimped portion of the terminal faces downward as shown in the illustration.



b.

Attach the No. 2 engine room wire clamp.


c.

Connect the starter assembly wire harness with the nut.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Connect the starter assembly connector.


Hide 19871 15.INSTALL NO. 1 GLOW PLUG CONNECTOR

Hide 16.INSTALL STARTER HOSE BRACKET SUB-ASSEMBLY

a.

Install the starter hose bracket sub-assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the 2 starter hoses to the starter assembly and starter hose bracket sub-assembly.


Hide 23763 17.CONNECT NO. 3 NOZZLE LEAKAGE PIPE

a.

Install the No. 3 nozzle leakage pipe with a new gasket and the union bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25620 18.INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER ASSEMBLY

Hide 25602 19.INSTALL NO. 2 EGR PIPE SUB-ASSEMBLY

Hide 25601 20.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 23801L 25.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

Hide 23820A 26.INSTALL COMMON RAIL ASSEMBLY LH

Hide 23810A 27.INSTALL COMMON RAIL ASSEMBLY RH

Hide 23705 28.INSTALL NO. 5 INJECTION PIPE SUB-ASSEMBLY

Hide 23805B 29.INSTALL NO. 5 FUEL PIPE SUB-ASSEMBLY

Hide 23706 31.INSTALL NO. 6 INJECTION PIPE SUB-ASSEMBLY

Hide 23702 32.INSTALL INJECTION PIPE SUB-ASSEMBLY LH

Hide 23701 33.INSTALL INJECTION PIPE SUB-ASSEMBLY RH

Hide 25850 36.INSTALL ELECTRIC VACUUM REGULATING VALVE ASSEMBLY

Hide 44761 38.INSTALL VACUUM PUMP TO CONNECTOR TUBE

Hide 44769 40.INSTALL VACUUM RESERVOIR CONNECT TUBE

Hide 23804D 41.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY

Hide 16264 43.CONNECT NO. 2 AND NO. 3 WATER BY-PASS HOSES

Hide 17947B 44.INSTALL NO. 3 INTERCOOLER SUPPORT BRACKET

Hide 26100G 46.INSTALL DIESEL THROTTLE BODY ASSEMBLY (for Bank 2)

Hide 26100G 47.INSTALL DIESEL THROTTLE BODY ASSEMBLY (for Bank 1)

Hide 82111 48.CONNECT ENGINE ROOM MAIN WIRE

a.

Connect the 20 connectors.


b.

Attach the 12 engine room main wire clamps.


c.

Install the 19 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Connect the generator wire with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


e.

Install the terminal cap.


Hide 17940D 53.INSTALL INTERCOOLER ASSEMBLY

Hide 87249B 55.CONNECT HEATER WATER OUTLET PIPE B

Hide 44774 56.CONNECT UNION TO CONNECTOR TUBE HOSE

Hide 82111 57.CONNECT ENGINE ROOM MAIN WIRE

a.

Connect the ECM connector.


b.

Connect the 4 injector driver connectors.


c.

Connect the 4 engine room main wire connectors.


d.

Attach the 4 engine room main wire clamps.


Hide 23271H 58.CONNECT NO. 1 AND NO. 2 FUEL HOSES

a.
A163861C01
1.167,3.75 1.333,3.75 1.333,3.75 1.573,4.094 true 1.583,3.333 1.75,3.333 1.75,3.333 2.302,3.115 true 0.583,2.417 0.75,2.417 0.75,2.417 0.948,2.927 true 2.5,0.917 2.333,0.917 2.333,0.917 2.104,1.667 true 2.333,0.667 2.167,0.667 2.167,0.667 1.938,1.417 true 1.01,3.656 1.323,3.813 0.313,0.156 10 false *1 0.333,2.99 0.646,3.146 0.313,0.156 10 false *a 0.875,2.479 1.188,2.635 0.313,0.156 10 false *b 2.396,2.469 2.708,2.625 0.313,0.156 10 false *c 0.438,2.313 0.75,2.469 0.313,0.156 10 false *d 1.708,3.604 2.021,3.76 0.313,0.156 10 false *e 2.073,4.417 2.385,4.573 0.313,0.156 10 false *f 1.865,2.99 2.177,3.146 0.313,0.156 10 false *a 1.438,3.229 1.75,3.385 0.313,0.156 10 false *d 0.917,3.406 1.073,3.604 0.156,0.198 10 false A 2.438,3.406 2.594,3.604 0.156,0.198 10 false B 1.542,1.99 1.781,2.24 0.24,0.25 10 true B 2.552,1.323 2.792,1.573 0.24,0.25 10 true A 2.521,0.833 2.833,0.99 0.313,0.156 10 true *2 2.354,0.583 2.667,0.74 0.313,0.156 10 true *3
*1 Clamp
*2 No. 1 Fuel Hose
*3 No. 2 Fuel Hose
*a Front
*b Upper
*c RH Side
*d White Paint
*e 2.0 to 7.0 mm (0.0787 to 0.276 in.)
*f 0 to 3.0 mm (0 to 0.118 in.)


Connect the No. 1 fuel hose to the fuel filter cap assembly, and slide the clamp to secure the hose.

HINT:
·

Position the claws of the clamps as shown in the illustration.

·

Install the clamps so that they are within the fuel hose paint marks.




b.

Connect the No. 2 fuel hose to the fuel pipe, and slide the clamp to secure the hose.

HINT:
·

Position the claws of the clamps as shown in the illustration.

·

Install the clamps so that they are within the fuel hose paint marks.




Hide 44778 59.CONNECT CONNECTOR TO CHECK VALVE HOSE

a.
A163856C01
2.01,2.583 2.667,2.833 2.667,2.833 2.833,2.833 true 1.771,0.146 2.083,0.302 0.313,0.156 10 false *a 1.052,1.021 1.365,1.177 0.313,0.156 10 false *b 2.844,2.75 3.167,3.031 0.323,0.281 10 true *c 1.469,0.354 1.927,0.552 0.458,0.198 10 false 30°
*a Upper
*b RH Side
*c White Paint


Connect the connector to check valve hose to the cylinder head cover sub-assembly, and slide the clamp to secure the hose.

HINT:
·

Position the claws of the clamp as shown in the illustration.

·

Install the clamp so that it is within the connector to check valve hose paint mark.




Hide 88320 60.CONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

a.

Install the cooler compressor assembly with the 4 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


b.

Connect the cooler compressor assembly connector.


Hide 44310 61.CONNECT VANE PUMP ASSEMBLY

a.

Coat a new O-ring with power steering fluid and connect it to the vane pump assembly.


b.

Install the vane pump assembly with the 2 new nuts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


c.

Connect the power steering oil pressure switch connector.


Hide 74403A 62.INSTALL BATTERY CARRIER SUB-ASSEMBLY

a.
A272904N01
1.313,0.354 1.542,0.573 0.229,0.219 10 true A 1.563,0.625 1.792,0.802 0.229,0.177 10 true B 2.5,0.438 2.729,0.656 0.229,0.219 10 true A 1.292,1.063 1.521,1.24 0.229,0.177 10 true B 2.5,1.052 2.729,1.229 0.229,0.177 10 true B

Install the battery carrier sub-assembly with the 5 bolts.

Torque:
for bolt A : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
for bolt B : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Attach the 3 wire harness clamps.


c.

Attach the clamp and connect the fusible link block to the battery carrier sub-assembly.


d.

Install the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.

Attach the wire harness clamp.


f.

Install the bolt and connect the engine wire.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


g.

Install the fusible link block cover.


h.

Attach the clamp and connect the No. 2 fuse block to the battery carrier sub-assembly.


i.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 28800 63.INSTALL BATTERY

a.

Install the battery and battery clamp with the bolt and nut.

Torque:
for bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
for nut : 5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 87246A 65.CONNECT HEATER WATER HOSE

a.
A163854C01
0.667,0.167 1.417,0.167 true 2.083,0.25 2.583,0.583 2.583,0.583 2.75,0.583 true 0.948,2.729 0.5,2.417 0.5,2.417 0.333,2.417 true 2.115,2.729 1.667,2.417 1.667,2.417 1.5,2.417 true 0.521,0.073 0.833,0.229 0.313,0.156 10 false *1 2.781,0.5 3.094,0.656 0.313,0.156 10 true *2 0.979,2.219 1.292,2.375 0.313,0.156 10 false *a 0.563,2.708 0.875,2.865 0.313,0.156 10 false *b 1.719,2.708 2.031,2.865 0.313,0.156 10 false *c 0.188,2.323 0.5,2.479 0.313,0.156 10 false *d 1.354,2.313 1.667,2.469 0.313,0.156 10 false *e 2.135,2.229 2.448,2.385 0.313,0.156 10 false *a 1.021,3.052 1.177,3.25 0.156,0.198 10 false A 2.188,3.052 2.344,3.25 0.156,0.198 10 false B 0.813,0.302 0.969,0.5 0.156,0.198 10 true A 1.927,0.667 2.146,0.865 0.219,0.198 10 true B
*1 Inlet Heater Water Hose
*2 Outlet Heater Water Hose
*a Upper
*b RH Side
*c Front
*d Yellow Paint
*e Blue Paint


Connect the inlet heater water hose to the outlet heater water pipe B, and slide the clamp to secure the hose.

HINT:
·

Position the claws of the clamps as shown in the illustration.

·

Install the clamps so that they are within the heater water hose paint marks.




b.

Connect the outlet heater water hose to the outlet heater water pipe B, and slide the clamp to secure the hose.

HINT:
·

Position the claws of the clamps as shown in the illustration.

·

Install the clamps so that they are within the heater water hose paint marks.




Hide 16400 66.INSTALL RADIATOR ASSEMBLY

Hide 69.CONNECT CABLE TO POSITIVE BATTERY TERMINAL

Hide 70.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 73.CHARGE REFRIGERANT (w/ Air Conditioning System)

Hide 74.WARM UP ENGINE (w/ Air Conditioning System)

Hide 75.INSPECT FOR REFRIGERANT LEAK (w/ Air Conditioning System)

Hide 53301 83.INSTALL HOOD SUB-ASSEMBLY

a.

Install the hood sub-assembly with the 4 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Connect the washer hose.