The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.
The normal conditions are as shown in the table below. The signals can be read using the GTS.
| Signals | Brake Pedal Released | In Transition | Brake Pedal Depressed |
|---|---|---|---|
| STP | OFF | ON | ON |
| ST1- | ON | ON | OFF |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0504 | Brake Switch "A" / "B" Correlation | Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch ON (b) Brake pedal released (c) STP signal OFF when ST1- signal OFF |
·
Short in stop light switch signal circuit
·
STOP fuse
·
IGN fuse
·
Stop light switch
·
ECM |
- | DTC stored |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
STP signal conditions can be checked using the GTS.
Connect the GTS to the DLC3.
Turn the ignition switch ON.
Turn the GTS ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.
Check the STP signal when the brake pedal is depressed and released.
| Brake Pedal Operation | Specified Condition |
|---|---|
| Depressed | STP signal ON |
| Released | STP signal OFF |
| *a | Front view of wire harness connector (to Stop Light Switch) |
Disconnect the I19 stop light switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I19-2 - Body ground | Always | 11 to 14 V |
| Proceed to |
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Stop Light Switch) |
Disconnect the I19 stop light switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I19-3 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
| OK |
| NG |
OK
NG
| *a | Component without harness connected (Stop Light Switch) |
Remove the stop light switch assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Switch pin released | Below 1 Ω |
| Switch pin pushed in | 10 kΩ or higher | |
| 3 - 4 | Switch pin released | 10 kΩ or higher |
| Switch pin pushed in | Below 1 Ω |
| Proceed to |
| OK |
| NG |
OK
NG
| *a | Brake Pedal Depressed |
| *b | Brake Pedal Released |
| *c | Front view of wire harness connector (to ECM) |
Disconnect the A29 ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-35 (ST1-) - Body ground | Released | 11 to 14 V |
| Depressed | 0 to 3 V | |
| A29-36 (STP) - Body ground | Released | 0 to 3 V |
| Depressed | 11 to 14 V |
| Proceed to |
| OK |
| NG |
OK
NG
Disconnect the I19 stop light switch connector.
Disconnect the L21 ignition switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I19-3 - L21-6 (IG2) | Always | Below 1 Ω |
| I19-3 or L21-6 (IG2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG