Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2014.08–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM J

1VD-FTV ENGINE CONTROL  ECD SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned ON, the battery voltage is applied to the IGSW of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the EFI MAIN1 relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

A225233E02
0.552,4.906 1.052,5.063 0.5,0.156 10 false Battery 0.448,4.281 1.25,4.438 0.802,0.156 10 false FL MAIN 1.083,0.677 1.417,0.854 0.333,0.177 10 false AM2 0.927,2.031 1.625,2.177 0.698,0.146 10 false EFI MAIN 3.469,3.083 3.938,3.229 0.469,0.146 10 false MAIN 4.073,2.271 4.198,2.427 0.125,0.156 10 false 3 3.156,2.271 3.281,2.427 0.125,0.156 10 false 5 2.469,0.969 2.656,1.125 0.188,0.156 10 false 5 2.667,0.969 3,1.125 0.333,0.156 10 false AM2 3.417,0.969 3.708,1.125 0.292,0.156 10 false IG2 4.885,0.698 5.177,0.854 0.292,0.156 10 false IGN 3.75,0.969 3.896,1.125 0.146,0.156 10 false 6 5.083,0.969 5.219,1.125 0.135,0.156 10 false 2 4.813,0.969 4.958,1.125 0.146,0.156 10 false 1 4.073,2.844 4.198,3 0.125,0.156 10 false 1 3.156,2.844 3.281,3 0.125,0.156 10 false 2 2.677,1.323 2.99,1.49 0.313,0.167 10 false L21 2.677,1.5 4.49,1.719 1.813,0.219 10 false Ignition Switch Assembly 5.865,0.854 6.177,1.021 0.313,0.167 10 false A29 6.198,0.75 6.635,0.917 0.438,0.167 10 false IGSW 6.198,2.188 6.635,2.354 0.438,0.167 10 false +B 5.906,0.677 6.115,0.833 0.208,0.156 10 false 28 5.854,3.281 6.167,3.448 0.313,0.167 10 false C39 6.198,3.281 6.635,3.448 0.438,0.167 10 false E1 5.906,3.104 6.115,3.26 0.208,0.156 10 false 81 5.865,2.188 6.177,2.354 0.313,0.167 10 false A29 5.969,2.01 6.115,2.167 0.146,0.156 10 false 2 6.198,2.74 6.635,2.906 0.438,0.167 10 false MREL 6.365,4.75 6.729,4.917 0.365,0.167 10 false ECM 5.875,2.75 6.188,2.917 0.313,0.167 10 false A29 5.927,2.573 6.125,2.729 0.198,0.156 10 false 44 0.927,3.802 1.74,3.948 0.813,0.146 10 false EFI MAIN 2 3.438,4.833 4.365,4.979 0.927,0.146 10 false MAIN 2 4.094,4.042 4.219,4.198 0.125,0.156 10 false 3 3.156,4.042 3.281,4.198 0.125,0.156 10 false 5 4.094,4.615 4.219,4.771 0.125,0.156 10 false 1 3.156,4.615 3.281,4.771 0.125,0.156 10 false 2 5.073,3.927 6.24,4.125 1.167,0.198 10 false to Sensor +B

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the C39 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C39-81 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT ECM (IGSW VOLTAGE)
a.
A311475C03
1.25,0.188 1.667,0.479 0.417,0.292 1.583,2.344 2,2.635 0.417,0.292 2.531,1.833 1.99,1.271 false 2.531,4.063 2.24,3.229 false 0.125,0.188 0.438,0.385 0.313,0.198 10 false *a 0.198,2.417 0.51,2.615 0.313,0.198 10 false *b 1.344,0.25 1.802,0.448 0.458,0.198 10 false C39 1.656,2.406 2.115,2.604 0.458,0.198 10 false A29 2.469,1.875 3.313,2.219 0.844,0.344 10 false 81 (E1) 2.448,4.115 3.281,4.51 0.833,0.396 10 false 28 (IGSW)
*a Front view of wire harness connector
(to ECM)
*b Front view of wire harness connector
(to ECM)


Disconnect the A29 and C39 ECM connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
A29-28 (IGSW) - C39-81 (E1) Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT MAIN RELAY (MAIN OR MAIN 2)

NG

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ECM)
3.INSPECT MAIN RELAY (MAIN OR MAIN 2)

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MAIN RELAY - ECM, MAIN 2 RELAY - ECM)

NG

REPLACE MAIN RELAY (MAIN OR MAIN 2)

4.CHECK HARNESS AND CONNECTOR (MAIN RELAY - ECM, MAIN 2 RELAY - ECM)
a.

Disconnect the A29 ECM connectors.


b.

Remove the MAIN or MAIN 2 relay from the engine room R/B assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
MAIN relay terminal 3 - A29-2 (+B) Always Below 1 Ω
MAIN relay terminal 1 - A29-44 (MREL) Always Below 1 Ω
MAIN 2 relay terminal 1 - A29-44 (MREL) Always Below 1 Ω
MAIN relay terminal 3 or A29-2 (+B) - Body ground Always 10 kΩ or higher
MAIN relay terminal 1 or A29-44 (MREL) - Body ground Always 10 kΩ or higher
MAIN 2 relay terminal 1 or A29-44 (MREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (MAIN RELAY - BATTERY, MAIN 2 RELAY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MAIN RELAY - BATTERY, MAIN 2 RELAY - BATTERY)
a.

Remove the MAIN or MAIN 2 relay from the engine room R/B assembly.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the cable from the positive (+) battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
MAIN relay terminal 5 - Battery positive (+) terminal Always Below 1 Ω
MAIN 2 relay terminal 5 - Battery positive (+) terminal Always Below 1 Ω
MAIN relay terminal 5 - Body ground Always 10 kΩ or higher
MAIN 2 relay terminal 5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (MAIN RELAY - BODY GROUND, MAIN 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MAIN RELAY - BODY GROUND, MAIN 2 RELAY - BODY GROUND)
a.

Remove the MAIN or MAIN 2 relay from the engine room R/B assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
MAIN relay terminal 2 - Body ground Always Below 1 Ω
MAIN 2 relay terminal 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ECM)
a.

Disconnect the L21 ignition switch connector.


b.

Disconnect the A29 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
L21-6 (IG2) - A29-28 (IGSW) Always Below 1 Ω
L21-6 (IG2) or A29-28 (IGSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>1VD-FTV (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH)

NG

REPLACE IGNITION SWITCH ASSEMBLY