Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2014.08–2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P0105  Manifold Absolute Pressure / Barometric Pressure Circuit  P0107  Manifold Absolute Pressure / Barometric Pressure Circuit Low Input  P0108  Manifold Absolute Pressure / Barometric Pressure Circuit High Input  


DESCRIPTION

A006532E15
0.385,0.49 0.521,0.688 0.135,0.198 10 false V 0.188,0.813 0.573,1.01 0.385,0.198 10 false 3.586 0.188,1.885 0.594,2.083 0.406,0.198 10 false 0.386 1.021,2.302 1.208,2.469 0.188,0.167 10 false 40 2.313,2.302 2.594,2.469 0.281,0.167 10 false 320 2.885,2.052 3.229,2.406 0.344,0.354 10 false kPa (abs) 2.885,2.531 3.333,2.708 0.448,0.177 10 false mmHg 2.885,2.875 3.333,3.063 0.448,0.188 10 false (in.Hg) 2.271,2.667 2.74,3.031 0.469,0.365 10 false 2400 (94.5) 0.958,2.667 1.354,3.031 0.396,0.365 10 false 300 (11.8) 1.365,3.083 2.167,3.26 0.802,0.177 10 false Air Pressure

The manifold absolute pressure sensor detects the intake manifold pressure by using its built-in sensor unit. The ECM determines the basic injection duration and injection advance timing based on the voltage output by the manifold absolute pressure sensor.

The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa (0 mmHg, 0 in.Hg)). As a result the ECM controls the air-fuel ratio at the proper level under any driving conditions, and fuel control accuracy is not influenced by fluctuations in the atmospheric pressure due to factors such as high altitude, etc.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0105 Manifold Absolute Pressure / Barometric Pressure Circuit After engine is started, condition (a) continues for more than 2.0 seconds
(1 trip detection logic)
(a) Open or short in manifold absolute pressure sensor circuit for 0.5 seconds or more
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored
P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input After engine is started, condition (a) continues for more than 2.0 seconds
(1 trip detection logic)
(a) Open or short in manifold absolute pressure sensor circuit for 0.5 seconds or more
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored
P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input After engine is started, condition (a) continues for more than 2.0 seconds
(1 trip detection logic)
(a) Open or short in manifold absolute pressure sensor circuit for 0.5 seconds or more
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored

HINT:

When DTC P0105, P0107 or P0108 is detected, check the intake manifold pressure by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / MAP.


Reference
Intake Manifold Pressure Malfunction
Approximately 0 kPa Short in PIM circuit
250 kPa (1875 mmHg, 73.8 in.Hg) or higher
·

Open or short in VC circuit

·

Open in PIM circuit

·

Open in E2 circuit



WIRING DIAGRAM

A165731E53
0.583,2.021 0.885,2.198 0.302,0.177 10 false C59 0.583,2.188 2.823,2.365 2.24,0.177 10 false Manifold Absolute Pressure Sensor 6.052,2.021 6.354,2.198 0.302,0.177 10 false C39 6.052,2.188 6.479,2.365 0.427,0.177 10 false ECM 1.604,1.615 1.76,1.76 0.156,0.146 10 false E 1.479,1.063 1.76,1.208 0.281,0.146 10 false PIM 1.521,0.479 1.76,0.625 0.24,0.146 10 false VC 5.698,1.594 5.927,1.74 0.229,0.146 10 false E2 5.698,1.042 5.979,1.188 0.281,0.146 10 false PIM 5.698,0.469 6.125,0.615 0.427,0.146 10 false VCPM 1.844,0.573 1.969,0.75 0.125,0.177 10 false 3 1.844,1.146 1.969,1.323 0.125,0.177 10 false 2 1.844,1.688 1.969,1.865 0.125,0.177 10 false 1 5.396,0.573 5.583,0.75 0.188,0.177 10 false 66 5.344,1.146 5.604,1.323 0.26,0.177 10 false 114 5.417,1.688 5.594,1.865 0.177,0.177 10 false 75

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (MANIFOLD ABSOLUTE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.

Powertrain > Engine and ECT > Data List
Tester Display
MAP
50003 61 314

d.

Read the value.

Standard:

Same value as the actual atmospheric pressure.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.
A311456C05
1.458,0.146 1.854,0.375 0.396,0.229 1.323,2.313 1.719,2.542 0.396,0.229 1.177,1.604 1.458,1.094 true 2.135,1.615 1.875,1.104 true 1.667,1.615 1.667,1.104 true 0.531,4.177 0.646,3.396 true 1.365,4.188 0.823,3.563 true 2.063,4.167 1.427,3.396 true 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 0.125,2.021 0.438,2.219 0.313,0.198 10 false *b 1.542,0.177 1.854,0.375 0.313,0.198 10 false C59 1.083,1.635 1.396,1.833 0.313,0.198 10 false E 1.583,1.646 1.896,1.844 0.313,0.198 10 false PIM 2.083,1.646 2.396,1.844 0.313,0.198 10 false VC 1.396,2.344 1.708,2.542 0.313,0.198 10 false C39 0.313,4.208 1.021,4.479 0.708,0.271 10 false 66 (VCPM) 1.25,4.208 1.906,4.542 0.656,0.333 10 false 114 (PIM) 2.01,4.208 2.594,4.427 0.583,0.219 10 false 75 (E2)
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)
*b Front view of wire harness connector
(to ECM)


Disconnect the C59 manifold absolute pressure sensor connector.


b.

Disconnect the C39 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C59-2 (PIM) - C39-114 (PIM) Always Below 1 Ω
C59-3 (VC) - C39-66 (VCPM) Always Below 1 Ω
C59-1 (E) - C39-75 (E2) Always Below 1 Ω
C59-2 (PIM) or C39-114 (PIM) - Body ground Always 10 kΩ or higher
C59-3 (VC) or C39-66 (VCPM) - Body ground Always 10 kΩ or higher
C59-1 (E) or C39-75 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)
a.
A165732C02
1.521,1.135 1.938,1.427 0.417,0.292 1.052,2.615 1.469,2.198 true 2.271,2.646 1.948,2.208 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 1.615,1.208 1.927,1.406 0.313,0.198 10 false C59 0.969,2.667 1.177,2.854 0.208,0.188 10 false E 2.26,2.677 2.5,2.833 0.24,0.156 10 false VC
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


Disconnect the C59 manifold absolute pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
C59-3 (VC) - C59-1 (E) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

4.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS

b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON and turn the GTS ON.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

f.

Read the DTC.

OK:

No DTC is output.



Result:
Proceed to
OK
NG



OK

END

NG