Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2014.08–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P1495  Intake Air Temperature Sensor 1 Circuit  P1496  Intake Air Temperature Sensor 1 Circuit Low  P1497  Intake Air Temperature Sensor 1 Circuit High  


DESCRIPTION

A208462E01
1.469,2 1.625,1.76 1.625,1.76 1.771,1.76 false 0.208,0.146 0.906,0.49 0.698,0.344 10 false (Fig. 1) 0.208,0.542 1.313,0.823 1.104,0.281 10 false Resistance kΩ 1.823,1.688 2.656,2.031 0.833,0.344 10 false Acceptable 1.208,4.073 2.521,4.385 1.313,0.313 10 false Temperature °C (°F)

The Intake Air Temperature (IAT) sensor is built into the charge air cooler and senses the IAT. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the greater the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (see Fig. 1).

The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the IAT, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1495 Intake Air Temperature Sensor 1 Circuit Open or short in intake air temperature (IAT) sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open or short in intake air temperature (IAT) sensor circuit

·

IAT sensor

·

ECM


Comes on DTC stored
P1496 Intake Air Temperature Sensor 1 Circuit Low Short in IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Short in IAT sensor circuit

·

IAT sensor

·

ECM


Comes on DTC stored
P1497 Intake Air Temperature Sensor 1 Circuit High Open in IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open in IAT sensor circuit

·

IAT sensor

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A165735E13
0.583,2.448 0.875,2.604 0.292,0.156 10 false C60 0.583,2.604 2.594,2.833 2.01,0.229 10 false Intake Air Temperature Sensor 6,2.677 6.292,2.833 0.292,0.156 10 false C39 6,2.833 6.354,3.01 0.354,0.177 10 false ECM 2.458,1.844 2.583,2.021 0.125,0.177 10 false 1 5.542,1.646 5.771,1.823 0.229,0.177 10 false E2 5.542,1.031 5.906,1.208 0.365,0.177 10 false THIA 2.458,1.229 2.583,1.406 0.125,0.177 10 false 2 5.292,1.844 5.49,2.021 0.198,0.177 10 false 75 5.302,1.229 5.49,1.406 0.188,0.177 10 false 74 6.156,0.917 6.281,1.073 0.125,0.156 10 false R 6.25,0.635 6.51,0.802 0.26,0.167 10 false 5V

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE [TURBO])
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air Temp (Turbo)
50003 61 240

d.

Read the value.

Standard value:

Same as air temperature near intake manifold.


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (same as air temperature near intake manifold) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or more.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A311472C02
1.521,2.677 1.948,2.948 0.427,0.271 0.615,1.74 0.927,1.896 0.313,0.156 10 false *1 2.677,1.938 2.99,2.094 0.313,0.156 10 false *2 0.281,2.51 0.594,2.667 0.313,0.156 10 false *a 1.615,2.74 1.927,2.896 0.313,0.156 10 false C60 2.406,1.073 2.979,1.26 0.573,0.188 10 false THIA 2.406,1.5 2.979,1.688 0.573,0.188 10 false E2
*1 IAT Sensor
*2 ECM
*a Front view of wire harness connector
(to IAT Sensor)


Disconnect the C60 intake air temperature (IAT) sensor connector.


b.

Connect terminals 1 and 2 of the IAT sensor wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch ON and turn the GTS ON.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air Temp (Turbo)
50003 61 240

f.

Read the value.

Standard value:

140°C (284°F) or higher



Result:
Proceed to
OK
NG



OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR

NG

3.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.
A311473C02
1.458,0.167 1.865,0.448 0.406,0.281 1.125,2.406 1.531,2.688 0.406,0.281 1.229,4.313 1.385,3.542 true 2.104,4.302 1.469,3.542 true 0.135,0.135 0.448,0.292 0.313,0.156 10 false *a 0.219,2.063 0.531,2.219 0.313,0.156 10 false *b 1.542,0.229 1.854,0.385 0.313,0.156 10 false C60 1.208,2.469 1.521,2.625 0.313,0.156 10 false C39 0.938,4.313 1.563,4.5 0.625,0.188 10 false 74 (THIA) 1.906,4.313 2.448,4.5 0.542,0.188 10 false 75 (E2)
*a Front view of wire harness connector
(to IAT Sensor)
*b Front view of wire harness connector
(to ECM)


Disconnect the C60 IAT sensor connector.


b.

Disconnect the C39 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C60-2 - C39-74 (THIA) Always Below 1 Ω
C60-1 - C39-75 (E2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the C60 IAT sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON and turn the GTS ON.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air Temp (Turbo)
50003 61 240

e.

Read the value.

Standard value:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.
A311473C03
1.458,0.167 1.865,0.448 0.406,0.281 1.125,2.406 1.531,2.688 0.406,0.281 1.229,4.313 1.385,3.542 true 2.104,4.302 1.469,3.542 true 0.135,0.135 0.448,0.292 0.313,0.156 10 false *a 0.219,2.063 0.531,2.219 0.313,0.156 10 false *b 1.573,0.219 1.885,0.375 0.313,0.156 10 false C60 1.208,2.458 1.521,2.615 0.313,0.156 10 false C39 0.938,4.313 1.563,4.5 0.625,0.188 10 false 74 (THIA) 1.906,4.313 2.448,4.5 0.542,0.188 10 false 75 (E2)
*a Front view of wire harness connector
(to IAT Sensor)
*b Front view of wire harness connector
(to ECM)


Disconnect the C60 IAT sensor connector.


b.

Disconnect the C39 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C60-2 or C39-74 (THIA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR