Home › Engine / Hybrid System › 1GR-FE (INTAKE / EXHAUST) › EXHAUST PIPE (for Model Code #J78, #J79 Series)
RM25T0E _51 Engine / Hybrid System _029771 1GR-FE INTAKE / EXHAUST _0135417 EXHAUST PIPE(for Model Code #J78, #J79 Series) A

1GR-FE INTAKE / EXHAUST  EXHAUST PIPE(for Model Code #J78, #J79 Series)  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

HINT:

Be sure to install the gasket so that it is flush with the installation surface and not at an angle.


a.

Inspect the compression spring.

i.
A104634

Using a vernier caliper, measure the free length of the compression spring.

Minimum free length:

38.9 mm (1.53 in.)


If the free length is less than the minimum, replace the compression spring.



b.
A104635C25
2.531,0.938 3.01,0.938 true 1.521,1.708 2.125,1.51 true 3.052,0.854 3.313,1.042 0.26,0.188 10 false *a 1.313,1.625 1.521,1.792 0.208,0.167 10 false *1
*1 Gasket
*a Wooden Block


Using a plastic-faced hammer and wooden block, tap a new gasket onto the exhaust manifold sub-assembly RH so that the gasket is flush with the exhaust manifold sub-assembly RH end.

NOTICE:
·

Install the gasket in the correct direction.

·

Do not damage the outer surface of the gasket.

·

Do not reuse the gasket.

·

Do not push in the gasket with the front exhaust pipe assembly when connecting it.




c.

for Double Cab:

Install the exhaust pipe damper to the front exhaust pipe assembly with 2 new nuts and 2 new bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


d.

for Double Cab:

Install the exhaust pipe support cushion to the front exhaust pipe assembly with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:
A218311C01
2.375,1.552 2.604,1.76 0.229,0.208 10 false *a
*a 40 mm (1.57 in.)


Be sure to install an exhaust pipe support cushion with a height of 40 mm (1.57 in.).



e.

Install the front exhaust pipe assembly to the exhaust manifold sub-assembly RH with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


f.

for Double Cab:

Connect the exhaust pipe support cushion with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17450 2.INSTALL NO. 2 FRONT EXHAUST PIPE ASSEMBLY

HINT:

Be sure to install the gasket so that it is flush with the installation surface and not at an angle.


a.

Inspect the compression spring.

i.
A104634

Using a vernier caliper, measure the free length of the compression spring.

Minimum free length:

38.9 mm (1.53 in.)


If the free length is less than the minimum, replace the compression spring.



b.
A104635C25
2.531,0.938 3.01,0.938 true 1.521,1.708 2.125,1.51 true 3.052,0.854 3.313,1.042 0.26,0.188 10 false *a 1.313,1.625 1.521,1.792 0.208,0.167 10 false *1
*1 Gasket
*a Wooden Block


Using a plastic-faced hammer and wooden block, tap a new gasket onto the exhaust manifold sub-assembly sub-assembly LH so that the gasket is flush with the pipe end.

NOTICE:
·

Install the gasket in the correct direction.

·

Do not damage the outer surface of the gasket.

·

Do not reuse the gasket.

·

Do not push in the gasket with the No. 2 front exhaust pipe assembly when connecting it.




c.

for Double Cab:

Install the exhaust pipe support cushion to the No. 2 front exhaust pipe assembly with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:
A218311C01
2.375,1.552 2.604,1.76 0.229,0.208 10 false *a
*a 40 mm (1.57 in.)


Be sure to install an exhaust pipe support cushion with a height of 40 mm (1.57 in.).



d.

Install the No. 2 front exhaust pipe assembly to the exhaust manifold sub-assembly LH with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


e.

for Double Cab:

Connect the exhaust pipe support cushion with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17420 4.INSTALL CENTER EXHAUST PIPE ASSEMBLY (for Double Cab)

HINT:

Be sure to install the gasket so that it is flush with the installation surface and not at an angle.


a.

Inspect the compression spring.

i.
A104634

Using a vernier caliper, measure the free length of the compression spring.

Minimum free length:

38.9 mm (1.53 in.)


If the free length is less than the minimum, replace the compression spring.



b.
A104635C25
2.531,0.938 3.01,0.938 true 1.521,1.708 2.125,1.51 true 3.052,0.854 3.313,1.042 0.26,0.188 10 false *a 1.313,1.625 1.521,1.792 0.208,0.167 10 false *1
*1 Gasket
*a Wooden Block


Using a plastic-faced hammer and wooden block, tap 2 new gaskets onto the front exhaust pipe assembly and No. 2 front exhaust pipe assembly so that the gaskets are flush with the pipe end.

NOTICE:
·

Install the gasket in the correct direction.

·

Do not damage the outer surface of the gasket.

·

Do not reuse the gasket.

·

Do not push in the gasket with the center exhaust pipe assembly when connecting it.




c.

Install the exhaust pipe support cushion to the center exhaust pipe assembly with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:
A273234C01
0.792,1.01 0.906,1.01 0.906,1.01 1.385,1.417 false 0.573,0.917 0.771,1.125 0.198,0.208 10 false *a 2.531,1.563 2.823,1.719 0.292,0.156 10 false *b
*a Heat Resistant Plate
*b 35 mm (1.38 in.)


Be sure to install an exhaust pipe support cushion with a height of 35 mm (1.38 in.) and heat resistant plate.



d.

Install the center exhaust pipe assembly with the 4 compression springs and 4 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


e.

Connect the exhaust pipe support cushion with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17420 5.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.

Install the exhaust pipe support cushion to the center exhaust pipe assembly with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:
A273235C01
2.542,1.594 2.792,1.771 0.25,0.177 10 false *a
*a 30 mm (1.18 in.)


Be sure to install an exhaust pipe support cushion with a height of 30 mm (1.18 in.).



b.

Install a new gasket and the center exhaust pipe assembly with 2 new bolts and 2 new nuts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


c.

Connect the exhaust pipe support cushion with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17404 6.INSTALL NO. 2 CENTER EXHAUST PIPE ASSEMBLY

a.

Install the exhaust pipe support cushion to the No. 2 center exhaust pipe assembly with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:
A273235C01
2.542,1.594 2.792,1.771 0.25,0.177 10 false *a
*a 30 mm (1.18 in.)


Be sure to install an exhaust pipe support cushion with a height of 30 mm (1.18 in.).



b.

Install a new gasket and the No. 2 center exhaust pipe assembly with 2 new bolts and 2 new nuts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


c.

Connect the exhaust pipe support cushion with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17407 7.INSTALL NO. 3 CENTER EXHAUST PIPE ASSEMBLY

HINT:

Be sure to install the gasket so that it is flush with the installation surface and not at an angle.


a.
A104635C25
2.531,0.938 3.01,0.938 true 1.521,1.708 2.125,1.51 true 3.052,0.854 3.313,1.042 0.26,0.188 10 false *a 1.313,1.625 1.521,1.792 0.208,0.167 10 false *1
*1 Gasket
*a Wooden Block


Using a plastic-faced hammer and wooden block, tap 2 new gaskets onto the center exhaust pipe assembly and No. 2 center exhaust pipe assembly so that the gaskets are flush with the pipe end.

NOTICE:
·

Install the gasket in the correct direction.

·

Do not damage the outer surface of the gasket.

·

Do not reuse the gasket.

·

Do not push in the gasket with the No. 3 center exhaust pipe assembly when connecting it.




b.

Install the No. 3 center exhaust pipe assembly with the 4 compression springs and 4 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17404 8.INSTALL NO. 2 CENTER EXHAUST PIPE ASSEMBLY (for Double Cab)

a.

Install a new gasket and the No. 2 center exhaust pipe assembly to the center exhaust pipe assembly with 2 new nuts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


Hide 17430 9.INSTALL TAILPIPE ASSEMBLY

A162132C01
1.604,0.469 2.104,0.219 2.104,0.219 2.26,0.219 true 2.313,0.135 2.625,0.333 0.313,0.198 10 false *a
*a New Gasket


a.

except Double Cab:

Install a new gasket to the No. 3 center exhaust pipe assembly.


b.

for Double Cab:

Install a new gasket to the No. 2 center exhaust pipe assembly.


c.

Install the exhaust pipe support cushion to the muffler clamp bracket with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:
A331817C01
2.01,0.583 2.51,0.583 true 0.208,0.167 0.521,0.323 0.313,0.156 10 false *A 0.198,2.427 0.51,2.583 0.313,0.156 10 false *B 2.552,0.479 2.865,0.635 0.313,0.156 10 false *a 2.479,1.729 2.792,1.885 0.313,0.156 10 false *b 2.479,3.948 2.792,4.104 0.313,0.156 10 false *c
*A for Model Code #J78 Series
*B for Model Code #J79 Series
*a Heat Resistant Plate
*b 35 mm (1.38 in.)
*c 30 mm (1.18 in.)


·

for Model Code #J78 Series:

Be sure to install an exhaust pipe support cushion with a height of 35 mm (1.38 in.) and heat resistant plate.

·

for Model Code #J79 Series:

Be sure to install an exhaust pipe support cushion with a height of 30 mm (1.18 in.).




d.

Install the 2 exhaust pipe support cushions to the tailpipe assembly with the 4 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:
A273235C01
2.542,1.594 2.792,1.771 0.25,0.177 10 false *a
*a 30 mm (1.18 in.)


Be sure to install an exhaust pipe support cushion with a height of 30 mm (1.18 in.).



e.

Install the tailpipe assembly with the 3 new bolts and 3 new nuts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


f.

Connect the exhaust pipe support cushion to the support bracket with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


g.

Connect the 2 exhaust pipe support cushions to the support bracket with the 4 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)