Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0135612 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The brake actuator assembly (skid control ECU) has an open detection circuit, which stores this DTC when detecting an open in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).

DTC No. Detection Item DTC Detection Condition Trouble Area
C1425 Open in Stop Light Switch Circuit When the IG1 terminal voltage is between 9.5 and 17.4 V, an open in the stop light circuit continues for 0.3 seconds or more.
·

Stop light circuit

·

STP terminal circuit

·

Brake actuator assembly (Skid control ECU)



WIRING DIAGRAM

C271025E04
0.75,0.938 2.208,1.125 1.458,0.188 10 false from Stop Light Switch 0.906,1.625 2.208,1.813 1.302,0.188 10 false to Stop Light Circuit 4.542,0.833 4.74,1.021 0.198,0.188 10 false 28 4.833,0.844 5.188,1.083 0.354,0.24 10 false STP 5.542,1.385 6.25,1.896 0.708,0.51 10 false Open Detection Circuit 4.854,2.219 5.333,2.417 0.479,0.198 10 false GND1 4.583,2.083 4.729,2.271 0.146,0.188 10 false 1 4.771,2.948 5.542,3.115 0.771,0.167 10 false A20 4.771,3.125 6.427,3.5 1.656,0.375 10 false Brake Actuator Assembly (Skid Control ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that all the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (STP TERMINAL)

NG

2.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the A20 brake actuator assembly (skid control ECU) connector.


c.
C260095C22
0.177,0.917 0.51,1.177 0.333,0.26 1.427,1.833 1.635,1.396 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.229,0.969 0.542,1.167 0.313,0.198 10 false A20 1.135,1.792 1.438,2 0.302,0.208 10 false STP
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A20-28 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC
a.

Connect the brake actuator assembly (skid control ECU) connector.


b.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Depress the brake pedal.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area.




DTC is not output

DTC is output