Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0135612 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1468  SFR Solenoid Circuit  C1469  SFL Solenoid Circuit  C146A  SRR Solenoid Circuit  


DESCRIPTION

These solenoids turn on when signals are received from the brake actuator assembly (skid control ECU) and they control the pressure acting on the wheel cylinders to control the braking force.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1468 SFR Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more.
·

Solenoid circuit

·

Brake actuator assembly


C1469 SFL Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more.
·

Solenoid circuit

·

Brake actuator assembly


C146A SRR Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more.
·

Solenoid circuit

·

Brake actuator assembly



WIRING DIAGRAM

C271786E03
1.927,1.354 2.688,1.5 0.76,0.146 10 false ABS SOL 0.438,1.167 1.25,1.365 0.813,0.198 10 false from Battery 3.188,1.083 3.365,1.24 0.177,0.156 10 false 12 3.24,4.969 3.344,5.125 0.104,0.156 10 false 1 3.458,1.271 3.75,1.427 0.292,0.156 10 false +BS 3.458,5.063 3.875,5.219 0.417,0.156 10 false GND1 4.448,1 5.448,1.208 1,0.208 10 false Solenoid Relay 4.375,4.146 5.542,4.344 1.167,0.198 10 false Skid Control ECU 5.865,1.948 6.271,2.104 0.406,0.156 10 false SFRH 5.865,2.469 6.25,2.625 0.385,0.156 10 false SFLH 5.854,2.958 6.271,3.115 0.417,0.156 10 false SRRH 5.865,3.469 6.271,3.625 0.406,0.156 10 false SFRR 5.854,3.979 6.26,4.135 0.406,0.156 10 false SFLR 5.854,4.479 6.271,4.635 0.417,0.156 10 false SRRR 3.427,8.229 4.094,8.385 0.667,0.156 10 false A20 3.427,8.396 5.104,8.552 1.677,0.156 10 false Brake Actuator Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.RECONFIRM DTC
HINT:

These codes are detected when a problem is determined in the brake actuator assembly.

The solenoid circuits are in the brake actuator assembly.

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the brake actuator assembly.


a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at the speed of 20 km/h (12 mph) or more for 30 seconds or more.


e.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the brake actuator assembly (skid control ECU), with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness from the brake actuator assembly (skid control ECU), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.





DTC is not output

DTC is output