When one of the following conditions is met, the ABS warning light remains on:
The brake actuator assembly (skid control ECU) connector is disconnected.
There is a malfunction in the brake actuator assembly (skid control ECU) internal circuit.
There is an open in the harness between the combination meter and the brake actuator assembly (skid control ECU).
The anti-lock brake system is defective.
w/ Rear Differential Lock:
The rear differential is locked or the rear differential and front differential are locked.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Before disconnecting the connector, make sure that there are no problems with the connection.
After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
Turn the ignition switch off.
Check if DTCs for the ABS are output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC is not output |
| DTC is output |
DTC is not output
DTC is output
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Check if the brake actuator assembly (skid control ECU) connector is securely connected.
The connector is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Brake Actuator Assembly [Skid Control ECU]) |
Disconnect the A20 brake actuator assembly (skid control ECU) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A20-34 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
| *a | Front view of wire harness connector (to Brake Actuator Assembly [Skid Control ECU]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A20-1 (GND1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the L25 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A20-21 (WA) - L25-16 (LP) | Always | Below 1 Ω |
| A20-21 (WA) or L25-16 (LP) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK (w/ Rear Differential Lock) |
| OK (w/o Rear Differential Lock) |
| NG |
OK (w/ Rear Differential Lock)
OK (w/o Rear Differential Lock)
NG
Turn the ignition switch to ON.
| *a | Front view of wire harness connector (to Brake Actuator Assembly [Skid Control ECU]) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A20-9 (EXI3) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| Outside of the specified condition |
| Within the specified condition |
Outside of the specified condition
Within the specified condition
Turn the ignition switch off.
Disconnect the V1 No. 4 transfer indicator switch (rear differential lock position switch) connector.
Disconnect the I8 No. 2 4 wheel drive control ECU (differential lock ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A20-9 (EXI3) - V1-2 | Always | Below 1 Ω |
| A20-9 (EXI3) or V1-2 - Body ground | Always | 10 kΩ or higher |
| A20-9 (EXI3) - L25-18 (RRSW) | Always | Below 1 Ω |
| A20-9 (EXI3) or L25-18 (RRSW) - Body ground | Always | 10 kΩ or higher |
| A20-9 (EXI3) - I8-2 (RLP) | Always | Below 1 Ω |
| A20-9 (EXI3) or I8-2 (RLP) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 4 transfer indicator switch (rear differential lock position switch).
Inspect the No. 4 transfer indicator switch (rear differential lock position switch).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>AXLE AND DIFFERENTIAL>DIFFERENTIAL LOCK CONTROL SWITCH (w/ Differential Lock)>REMOVAL
Turn the ignition switch off.
Connect the brake actuator assembly (skid control ECU) connector.
Connect the combination meter assembly connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| ABS Warning Light | ABS warning light | Warning light ON / OFF | Observe the combination meter. |
When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ABS Warning Light | ABS warning light | ON or OFF | ON: ABS warning light on OFF: ABS warning light off |
- |
| Active Test Display |
|---|
| ABS Warning Light |
| Data List Display |
|---|
| ABS Warning Light |
| Result | Proceed to | |
|---|---|---|
| Data List Display | Data List Display When Performing Active Test ON/OFF Operation | |
| ON | Does not change between ON and OFF | A |
| Changes between ON and OFF | B | |
| OFF | Does not change between ON and OFF | A |
| Changes between ON and OFF | B | |
A
B
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING