Home › Engine / Hybrid System › 1HZ (FUEL) › FUEL TANK(for 90 L Tank Carried in Middle) › 2014.08–2016.08
RM25T0E _51 Engine / Hybrid System _029893 1HZ FUEL _0136496 FUEL TANK(for 90 L Tank Carried in Middle) A

1HZ FUEL  FUEL TANK(for 90 L Tank Carried in Middle)  INSTALLATION  


PROCEDURE

Hide 77011 1.INSTALL LOWER FUEL TANK FILLER PIPE SUB-ASSEMBLY

a.

Install a new gasket and the lower fuel tank filler pipe sub-assembly with the 6 screws.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 2.INSTALL FUEL SUCTION TUBE ASSEMBLY

a.

Install a new gasket and the fuel suction tube assembly with the 5 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


Hide 77420 4.INSTALL NO. 2 FUEL CUT OFF VALVE ASSEMBLY

a.

Install the No. 2 fuel cut off valve assembly onto the fuel tank assembly.


Hide 77380 5.INSTALL FUEL CUT OFF VALVE ASSEMBLY

a.

Install the fuel cut off valve assembly onto the fuel tank assembly.


Hide 77026A 6.INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Install 2 new gaskets and the No. 1 evaporation tube sub-assembly to the fuel tank assembly with the 8 screws and 2 nuts.

Torque:
for screw : 1.5 N*m (15 kgf*cm, 13 in.*lbf)
for nut : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 77100 7.INSTALL FUEL TANK

a.

Set the fuel tank and fuel tank protector on an engine lifter.


b.

Raise the engine lifter.


c.

Connect the 2 fuel tank bands with the 2 bolts.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


d.

Connect the fuel sender gauge connector.


Hide 77100D 8.CONNECT FUEL BREATHER HOSE

a.

Connect the fuel breather hose to the fuel tank assembly, and slide the clamp to secure the hose.


Hide 77213 9.CONNECT INLET FUEL HOSE

a.

Connect the inlet fuel hose to the lower fuel tank filler pipe sub-assembly, and slide the clamp to secure the hose.


Hide 10.CONNECT FUEL RETURN HOSE

a.

Connect the fuel return hose to the fuel suction tube assembly, and slide the clamp to secure the hose.


Hide 11.CONNECT FUEL MAIN HOSE

a.

Connect the fuel main hose to the fuel suction tube assembly, and slide the clamp to secure the hose.


Hide 77207B 12.INSTALL NO. 3 FUEL MAIN TUBE SUB-ASSEMBLY

a.

for Single Tank Type:

i.

Install the No. 3 fuel main tube sub-assembly with the bolt.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


ii.

Connect the 4 fuel hoses to the No. 3 fuel main tube sub-assembly, and slide the 4 clamps to secure the 4 hoses.



b.

for Double Tank Type:

i.

Install the fuel No. 3 main tube sub-assembly with the 2 bolts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


ii.

Connect the 4 fuel hoses to the No. 3 fuel main tube sub-assembly, and slide the 4 clamps to secure the 4 hoses.



Hide 37110 13.INSTALL PROPELLER SHAFT ASSEMBLY

Hide 17420 14.INSTALL CENTER EXHAUST PIPE ASSEMBLY

Hide 17430 15.INSTALL TAILPIPE ASSEMBLY

Hide 16.BLEED AIR FROM FUEL SYSTEM