Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › ENGINE › 2014.08–2021.12
RM25T0E _51 Engine / Hybrid System _029891 1GR-FE ENGINE MECHANICAL _0136552 ENGINE G

1GR-FE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 17801 4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.


b.

Visually check that the air cleaner filter element sub-assembly is not excessively damaged or oily.

If necessary, replace the air cleaner filter element sub-assembly.


c.

Install the air cleaner filter element sub-assembly.


Hide 6.INSPECT IGNITION TIMING

NOTICE:

Turn all of the electrical systems off.


a.

Warm up the engine and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Start the engine.


v.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
IGN Advance
50004 61 13 317

vi.

Inspect the ignition timing during idling.

Standard ignition timing:

8 to 12° BTDC @ idle (transmission in neutral position and A/C switch off)



vii.

Cancel the Active Test.


viii.

Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

Powertrain > Engine and ECT > Data List
Tester Display
IGN Advance
50003 61 317

ix.

Inspect the ignition timing during idling.

Standard ignition timing:

7 to 24° BTDC @ idle (transmission in neutral position and A/C switch off)



x.

Check that the ignition timing advances immediately when the engine speed is increased.



c.

When not using the GTS:

i.
A206183C78
1.188,0.531 1.385,0.531 1.385,0.531 1.594,0.906 true 1.771,1.469 1.906,1.865 1.906,1.865 2.125,1.865 true 0.052,0.063 0.365,0.26 0.313,0.198 10 false *a 0.958,0.458 1.271,0.656 0.313,0.198 10 false CG 2.177,1.802 2.49,2 0.313,0.198 10 false TC
*a Front view of DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:

Do not improperly connect the terminals. This may damage the engine.



ii.
A270442

Pull out the wire harness shown in the illustration.


iii.

Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

NOTICE:
·

Use a timing light that detects primary signals.

·

After checking, be sure to wrap the wire harness with tape.




iv.

Start the engine.


v.

Inspect the ignition timing during idling.

Standard ignition timing:

8 to 12° BTDC @ idle (transmission in neutral position and A/C switch off)



vi.

Remove SST from the DLC3.


vii.

Inspect the ignition timing during idling.

Standard ignition timing:

7 to 24° BTDC @ idle (transmission in neutral position and A/C switch off)



viii.

Disconnect the timing light from the engine.



Hide 7.INSPECT ENGINE IDLE SPEED

NOTICE:

Turn all of the electrical systems off.


a.

Warm up the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Start the engine.


iv.

Turn the GTS on.


v.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 61 315

vi.

Inspect the engine idle speed.

Standard idle speed:

650 to 750 rpm (transmission in neutral position and A/C switch off)




c.

When not using the GTS:

i.
A206183C80
0.583,1.896 0.771,1.896 0.771,1.896 1,1.479 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 0.281,1.813 0.594,2.01 0.313,0.198 10 false TAC
*a Front view of DLC3


Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.

SST
09843-18030  


ii.

Race the engine at 2500 rpm for approximately 90 seconds.


iii.

Inspect the engine idle speed.

Standard idle speed:

650 to 750 rpm (transmission in neutral position and A/C switch off)



iv.

Disconnect the tachometer probe from the DLC3.



Hide 8.INSPECT COMPRESSION

NOTICE:
·

When measuring compression, prevent foreign objects from entering the intake manifold and plug hole.

·

After finishing all work, check that normal codes are output after clearing all DTCs.



a.

Warm up and stop the engine.


b.

c.


e.

Disconnect the 6 fuel injector connectors.

NOTICE:

Stop fuel injection to prevent damage to the catalyst due to unburned fuel.



f.

Inspect the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

While cranking the engine, measure the compression pressure.

Compression pressure:

1300 kPa (13.3 kgf/cm2, 189 psi) or higher


Minimum pressure:

1000 kPa (10.2 kgf/cm2, 145 psi)


Difference between each cylinder:

100 kPa (1.0 kgf/cm2, 15 psi) or less


HINT:
·

Use a fully-charged battery so that the engine speed can be increased to 250 rpm or more.

·

Measure the compression in as short a time as possible.




iii.

If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole, and then inspect it again.

HINT:
·

If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.

·

If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage from the gasket.





g.

Connect the 6 fuel injector connectors.





Hide 9.INSPECT CO/HC

HINT:

This check is to determine whether or not the idle CO/HC concentration complies with regulations.


a.

Start the engine.


b.

Run the engine at 2500 rpm for approximately 180 seconds.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.


d.

Immediately check the CO/HC concentration during idling and/or at 2500 rpm.

HINT:

When carrying out the 2 tests (idling and 2500 rpm), the measurement orders are prescribed by the applicable local regulations.



e.

If the CO/HC concentration does not comply with regulations, perform troubleshooting in the order given below.

i.

Check for DTCs.


ii.

Check the air fuel ratio sensor operation.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION


iii.

Check the heated oxygen sensor operation.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>HEATED OXYGEN SENSOR>INSPECTION


iv.

Refer to the table below for possible causes, and then inspect and correct the corresponding causes if necessary.

CO HC Problem Possible Cause
Normal High Rough idling
1.

Faulty ignition:

-

Incorrect timing

-

Fouled, shorted or improperly gapped plugs


2.

Incorrect valve clearance

3.

Leaky intake and exhaust valves

4.

Leaky cylinders


Low High Rough idling
(Fluctuating HC reading)
1.

Vacuum leaks:

-

Ventilation hoses

-

Intake manifold

-

Throttle body

-

Brake booster line


2.

Lean mixture causing misfire


High High Rough idling
(Black smoke from exhaust)
1.

Restricted air clearner filter element sub-assembly

2.

Faulty SFI system:

-

Faulty fuel pressure regulator assembly

-

Defective engine coolant temperature sensor

-

Faulty mass air flow meter

-

Faulty ECM

-

Faulty fuel injector assemblies

-

Faulty throttle position sensor