Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › IGNITION SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135350 IGNITION SYSTEM G

1GR-FE ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.PERFORM SPARK TEST

a.

Check for DTCs.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

If any DTC is output, perform the troubleshooting procedures for that DTC.



b.

Check if sparks occur.

i.

Remove the 6 ignition coil assemblies and 6 spark plugs.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL


ii.

Install the spark plug to the ignition coil assembly and connect the ignition coil connector.


iii.

Disconnect the fuel pump connector.

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION


iv.

Ground the spark plug.


v.

Visually check that sparks occur while the engine is being cranked.

NOTICE:
·

Be sure to ground the spark plug when checking.


·

Replace the ignition coil assembly if it receives an impact.


·

Do not crank the engine for more than 2 seconds.





Hide 2.INSPECT IGNITION COIL AND SPARK TEST

a.

Check that the wire harness side connector of the ignition coil assembly is securely connected.

Result
Result Proceed to
NG Connect securely
OK Go to next step


b.

Perform a spark test on each ignition coil assembly.

i.

If there is a cylinder where sparks do not occur, replace its ignition coil assembly with the ignition coil of a cylinder where sparks occur normally.


ii.

Crank the engine and visually check that sparks occur at the cylinder with the normally operating ignition coil assembly.

Result
Result Proceed to
OK Replace ignition coil assembly
NG Go to next step



c.

Inspect the spark plug.

i.

Replace the spark plug with a normal one.


ii.

Perform spark test again.

Result
Result Proceed to
OK Replace spark plug
NG Go to next step



d.

Check the power supply to the ignition coil assembly.

i.

Turn the ignition switch to ON.


ii.

Check that there is battery voltage at the ignition coil positive (+) terminal.

Result
Result Proceed to
NG Check wiring between ignition switch and ignition coil assembly
OK Go to next step




f.

Check the crankshaft position sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0335


g.

Check the IGT signal circuit.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0351


h.

Install the 6 ignition coil assemblies and 6 spark plugs.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>INSTALLATION


i.

Connect the fuel pump connector.



Hide 19100P 3.CHECK SPARK PLUG

a.
I039522C35
0.865,1.917 1.063,1.917 false 0.698,1.833 0.875,2.031 0.177,0.198 10 false *a
*a Body Ground


Check the electrode.

i.

Using a megohmmeter, measure the insulation resistance.

Standard Insulation Resistance:
Tester Connection Condition Specified Condition
Spark plug (terminal part) - Body ground Always 10 MΩ or higher


If a megohmmeter is not available, perform the following simple inspection.



b.

Alternative inspection method:

i.

Quickly accelerate the engine to 4000 rpm 5 times.


ii.

Remove the spark plug.


iii.

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.



c.

Check the spark plug for any damage on its threads and insulator.

If there is damage, replace the spark plug.


d.
A303022

Clean the spark plugs.


e.

Check and adjust the electrode gap.

Recommended Spark Plug and Electrode Gap:
Manufacturer Product Electrode gap for new spark plug Maximum electrode gap for used spark plug
DENSO made K20HR-U11 1.0 to 1.1 mm (0.0394 to 0.0433 in.) 1.3 mm (0.0512 in.)
NGK made LFR6C-11


If the gap is more than the maximum, replace the spark plug.