Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › ENGINE UNIT
RM25T0E _51 Engine / Hybrid System _029891 1GR-FE ENGINE MECHANICAL _0136560 ENGINE UNIT A

1GR-FE ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


PROCEDURE

Hide 87209 1.REMOVE WATER HOSE SUB-ASSEMBLY

a.
A222567

Slide the hose clamp and remove the nut and water hose sub-assembly.


Hide 87246A 2.REMOVE OUTLET HEATER WATER HOSE

a.
A332552

Slide the hose clamp and remove the outlet heater water hose.


Hide 23801P 3.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY AND NO. 2 FUEL PIPE SUB-ASSEMBLY

Hide 23807 4.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23250 5.REMOVE FUEL INJECTOR ASSEMBLY

Hide 7.REMOVE ENGINE WIRE

a.

Remove the engine wire.


Hide 16620 9.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A175285

Remove the 5 bolts and V-ribbed belt tensioner assembly.


Hide 12311 10.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.
A218519

Remove the 4 bolts and front No. 1 engine mounting bracket RH.


Hide 12315 11.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.
A218520

Remove the 3 bolts and front No. 1 engine mounting bracket LH.


Hide 16603 12.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A326600

Remove the bolt and No. 1 idler pulley sub-assembly.


Hide 16604 13.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

a.
A326601C01
0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 1.833,0.073 2.146,0.271 0.313,0.198 10 false *b
*a RH
*b LH


for Cover Separate Type:

Remove the 2 bolts, 2 idler pulley cover plates, 2 No. 2 idler pulley cover plates and 2 No. 2 idler pulley sub-assemblies.


b.

for Cover Integrated Type:

Remove the 2 bolts and 2 No. 2 idler pulley sub-assemblies.


Hide 13453 14.REMOVE FLYWHEEL RING GEAR

CAUTION:

Wear protective gloves. Hot areas on the flywheel ring gear may injure your hands.


HINT:

If the flywheel ring gear is deformed or damaged, replace it.


a.
A326602N01
1.031,2.698 1.188,2.896 0.156,0.198 10 false 1 2.01,2.646 2.167,2.844 0.156,0.198 10 false 6 2.688,3.344 2.844,3.542 0.156,0.198 10 false 4 2.292,3.969 2.479,4.135 0.188,0.167 10 true 2 1.385,4.021 1.573,4.188 0.188,0.167 10 true 5 0.594,3.531 0.781,3.698 0.188,0.167 10 false 3

Using a torch, heat the ring flywheel ring gear evenly to approximately 200°C (392°F).


b.

Temporarily install 6 bolts (8 mm x 1.25 pitch) with a length of 70 mm (2.76 in.) or more to the flywheel sub-assembly.


c.

Uniformly tighten the 6 bolts in the order shown in the illustration.


d.

Remove the flywheel ring gear from the flywheel sub-assembly.