Home › Engine / Hybrid System › 1GR-FE (LUBRICATION) › OIL PUMP
RM25T0E _51 Engine / Hybrid System _029523 1GR-FE LUBRICATION _0133820 OIL PUMP A

1GR-FE LUBRICATION  OIL PUMP  REMOVAL  


PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Air Conditioning System)

Hide 16711 6.REMOVE FAN SHROUD

Hide 88320 7.REMOVE COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 16631B 8.REMOVE IDLER PULLEY BRACKET (w/o Air Conditioning System)

a.
A328790

Remove the 3 bolts and idler pulley bracket.


Hide 27020 9.REMOVE GENERATOR ASSEMBLY

Hide 44310 10.DISCONNECT VANE PUMP ASSEMBLY

Hide 88712 11.DISCONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE (w/ Air Conditioning System)

a.
A221943

for LHD:

Remove the bolt and disconnect the No. 1 cooler refrigerant suction hose.


Hide 82127 12.DISCONNECT NO. 7 ENGINE WIRE

a.
A218596

Remove the bolt and disconnect the No. 7 engine wire.


Hide 23801P 13.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY AND NO. 2 FUEL PIPE SUB-ASSEMBLY

a.
A331138

Remove the No. 1 fuel pipe clamp and 2 No. 2 fuel pipe clamps.


b.

Disconnect the No. 1 fuel pipe sub-assembly and No. 2 fuel pipe sub-assembly.

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION


c.

Remove the 2 bolts, No. 1 fuel pipe sub-assembly and No. 2 fuel pipe sub-assembly.


Hide 15340 17.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY LH (for Bank 1)

Hide 15330B 18.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY RH (for Bank 2)

Hide 87245A 19.REMOVE INLET HEATER WATER HOSE

a.
A221982

Slide the 2 clamps and remove the inlet heater water hose.


Hide 87209 20.REMOVE WATER HOSE SUB-ASSEMBLY

a.
A221983

Slide the clamp and disconnect the water hose sub-assembly.


b.

Remove the bolt and water hose sub-assembly.


Hide 87246A 21.REMOVE OUTLET HEATER WATER HOSE

a.
A221984

Slide the 2 clamps and remove the outlet heater water hose.


Hide 22.DISCONNECT CLUTCH TUBE

a.
A221960

Remove the bolt and disconnect the clutch tube.


Hide 23.DISCONNECT WIRE HARNESS

Hide 11202 24.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 11201 25.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 16356 26.REMOVE REAR WATER BY-PASS JOINT

a.

Disconnect the engine coolant temperature sensor connector.


b.
A218547

Remove the 2 bolts, 4 nuts and rear water by-pass joint.


c.

Remove the 2 gaskets and O-ring.


Hide 16620 27.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16604 28.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 16603 29.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 12102A 31.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15104 32.REMOVE OIL STRAINER SUB-ASSEMBLY

Hide 11361J 33.REMOVE UNDER FLYWHEEL HOUSING COVER

a.
A221957

Remove the under flywheel housing cover.


Hide 12101 34.REMOVE OIL PAN SUB-ASSEMBLY

a.
A221959

Remove the 4 bolts.


b.
A222082

Remove the 17 bolts and 2 nuts.


c.
A327366C01
2.448,0.823 2.698,0.406 2.698,0.406 2.865,0.406 true 0.438,1.771 0.75,1.927 0.313,0.156 10 false *a 0.427,3.323 0.74,3.479 0.313,0.156 10 false *b 2.906,0.323 3.219,0.479 0.313,0.156 10 false *c 2.531,1.177 2.844,1.333 0.313,0.156 10 false *d
*a LH Side
*b RH Side
*c Protective Tape
*d Pry


Using a screwdriver, remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly as shown in the illustration.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.


HINT:

Tape the screwdriver tip before use.



d.
A326607

Remove the O-ring from the timing chain cover sub-assembly.


Hide 15778 35.DISCONNECT NO. 2 OIL COOLER HOSE

Hide 15777 36.DISCONNECT OIL COOLER HOSE

Hide 15609 38.REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

Hide 11302 39.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11301C 40.REMOVE FRONT CRANKSHAFT OIL SEAL