Home › Drivetrain › CLUTCH › CLUTCH PEDAL (for LHD) › 2014.08–2017.01
RM25T0E _52 Drivetrain _029901 CLUTCH _0136564 CLUTCH PEDAL(for LHD) A

CLUTCH  CLUTCH PEDAL(for LHD)  INSTALLATION  


PROCEDURE

Hide 31301F 1.INSTALL CLUTCH PEDAL STOPPER BOLT

a.
C163052

Install the lock nut to the clutch pedal stopper bolt.


b.

Temporarily install the clutch pedal stopper bolt to the clutch pedal support sub-assembly.

HINT:

Tighten the lock nut to the specified torque when adjusting the clutch pedal.



Hide 31353 2.INSTALL CLUTCH PEDAL SPRING HOLDER

a.
C310580C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the contact surface of the clutch pedal spring holder.


b.

Install the clutch pedal spring holder to the clutch pedal support sub-assembly.


Hide 31453B 3.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSH

a.
C310581C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the inside of a new clutch master cylinder push rod clevis bush.


b.

Install the clutch master cylinder push rod clevis bush to the clutch pedal sub-assembly.

HINT:

Install the clevis bush from the left side of the vehicle.



Hide 31301P 4.INSTALL CLUTCH PEDAL TURNOVER BUSH

a.
C310582C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the inside of the clutch pedal turnover bush.


b.

Install the clutch pedal turnover bush to the clutch pedal sub-assembly.


Hide 31301B 5.INSTALL NO. 1 CLUTCH PEDAL CUSHION

a.
C163082

Install the No. 1 clutch pedal cushion to the clutch pedal sub-assembly.


Hide 31301C 6.INSTALL CLUTCH PEDAL BUSH

a.
C310583C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the inside and outside of 2 new clutch pedal bushes.


b.

Install the 2 clutch pedal bushes to the clutch pedal sub-assembly.


Hide 31324A 7.INSTALL CLUTCH PEDAL SHAFT COLLAR

a.
C310584C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the clutch pedal shaft collar.


b.

Install the clutch pedal shaft collar to the clutch pedal sub-assembly.


Hide 31321 8.INSTALL CLUTCH PEDAL PAD

Hide 31301 9.INSTALL CLUTCH PEDAL SUB-ASSEMBLY

a.
C163053

Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt and nut.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)

HINT:

Install the bolt from the left side of the vehicle.



Hide 31434 10.INSTALL CLUTCH RESERVOIR TUBE

a.
C310579

Connect the clutch reservoir tube to the clutch master cylinder assembly, and slide a new clamp to secure it.


Hide 31410 11.INSTALL CLUTCH MASTER CYLINDER ASSEMBLY

Hide 31301A 12.INSTALL CLUTCH PEDAL SPRING (for 1GR-FE)

a.
C310586C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the inside and outside of the spacer and pin of the clutch pedal support sub-assembly.


b.

Install the spacer to the clutch pedal spring.


c.

Install the clutch pedal spring to the clutch pedal support sub-assembly with 2 new E-rings.


Hide 31301R 13.INSTALL TURN OVER SPRING SEAT COMPRESSION SPRING

a.
C310587C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the contact surfaces of the clutch pedal spring holder, clutch pedal and turn over spring seat compression spring.


b.

Move the pedal to the full stroke position.


c.

Install the turn over spring seat compression spring to the clutch pedal sub-assembly and clutch pedal spring holder.


Hide 31331B 14.INSTALL CLUTCH PEDAL SUPPORT WAY

a.
C163051

Install the clutch pedal support way to the clutch pedal support sub-assembly with the screw.

Torque:
4.5 N*m (46 kgf*cm, 40 in.*lbf)


b.

Connect the clutch reservoir tube to the clutch pedal support way, and slide a new clamp to secure it.


c.

Install the clutch pedal support grommet.


Hide 31481J 15.INSTALL CLUTCH MASTER CYLINDER TO 2 WAY TUBE

a.
C310588C01
1.302,1.896 1.615,2.094 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the clutch master cylinder to 2 way tube to the clutch master cylinder assembly and clutch pedal support way.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)




Hide 16.INSTALL CLUTCH PEDAL SUPPORT ASSEMBLY WITH CLUTCH MASTER CYLINDER

a.
C162777

Install the clutch pedal support assembly with clutch master cylinder with the bolt and 2 nuts.

Torque:
for bolt : 19 N*m (194 kgf*cm, 14 ft.*lbf)
for nut : 14.2 N*m (145 kgf*cm, 10 ft.*lbf)


Hide 55833D 17.INSTALL NO. 1 INSTRUMENT PANEL REGISTER CONNECTOR (w/ Heater)

Hide 55844 18.INSTALL NO. 2 HEATER TO REGISTER DUCT

Hide 55480D 19.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 86160 20.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

Hide 31481 21.CONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE AND CLUTCH RESERVOIR TUBE

a.
C310589C01
1.615,1.688 1.927,1.885 0.313,0.198 10 true *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the flexible hose tube.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)




b.

Connect the clutch reservoir tube to the clutch pedal support way, and slide a new clamp to secure it.


Hide 22.FILL RESERVOIR WITH BRAKE FLUID

Hide 23.BLEED CLUTCH PIPE LINE

Hide 24.CHECK BRAKE FLUID LEVEL IN RESERVOIR

Hide 25.CHECK FOR CLUTCH FLUID LEAK

Hide 31301 26.INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY