Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) › 2014.08–2016.08
RM25T0E _52 Drivetrain _029907 AXLE AND DIFFERENTIAL _0137074 FRONT DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock) A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock)  REASSEMBLY  


PROCEDURE

Hide 41252A 1.INSTALL FRONT DIFFERENTIAL DUST DEFLECTOR

a.
C161289N01
1.281,0.253 1.579,0.403 0.298,0.151 10 SST 2.176,1.327 1.937,0.322 false 1.937,0.322 1.641,0.322 false

Using SST, a press and steel plate, press in a new front differential dust deflector.

SST
09726-40010  

NOTICE:

Be careful not to damage the front differential dust deflector.



Hide 2.ASSEMBLE DIFFERENTIAL CASE

a.
C161342

Apply hypoid gear oil to each part.


b.

Install the front No. 1 differential side gear thrust washer to the front differential side gear.


c.

Install the front differential side gear to the front differential case RH.


d.

Install the 4 front differential pinions and 4 front differential pinion thrust washers to the front differential spider.


e.
C161343

Install the front differential pinions and front differential spider to the front differential case RH.


f.
C161344

While holding the front differential side gear and front differential spider, measure the side gear backlash.

Standard backlash:

0.05 to 0.20 mm (0.00197 to 0.00787 in.)


HINT:
·

Measure at all 4 locations.

·

Measure the backlash at the front differential case LH and RH.


If the backlash is not within the specification, install a side gear thrust washer of a different thickness.

Standard Side Gear Thrust Washer Thickness:
Thickness Thickness
0.88 to 0.92 mm (0.0347 to 0.0362 in.) 1.18 to 1.22 mm (0.0465 to 0.0480 in.)
0.98 to 1.02 mm (0.0386 to 0.0401 in.) 1.28 to 1.32 mm (0.0504 to 0.0519 in.)
1.08 to 1.12 mm (0.0426 to 0.0440 in.) -





g.

Install the front differential side gear and front No. 1 differential side gear thrust washer to the front differential case RH.


h.

Install the 4 front differential pinions, 4 front differential pinion thrust washers and front differential spider to the front differential case RH.


i.
C161345

Install the front differential side gear and front No. 1 differential side gear thrust washer to the front differential case RH.


j.
C161346C01
1.219,1.51 2.104,1.677 2.104,1.677 1.219,1.625 true 2.177,1.594 2.896,1.75 0.719,0.156 10 false *a
*a Matchmark


Align the matchmarks on the front differential case LH and RH.


k.

Tighten the 8 bolts.

Torque:
47.1 N*m (480 kgf*cm, 35 ft.*lbf)


Hide 41311A 3.INSTALL FRONT DIFFERENTIAL CASE BEARING

a.
C311262N01
0.667,0.865 0.531,0.635 0.531,0.635 0.792,0.646 false 0.656,2.75 0.542,2.604 0.542,2.604 0.802,2.646 false 0.479,4.177 0.573,4.177 0.573,4.177 0.688,4.229 true 0.229,0.563 0.688,0.76 0.458,0.198 10 false SST 0.26,2.521 0.719,2.719 0.458,0.198 10 false SST 0.198,4.104 0.656,4.302 0.458,0.198 10 false SST

Using SST and a press, install the 2 front differential case bearings (inner race) to the front differential case.

SST
09223-15020  
09950-60010  (09951-00480, 09951-00550)
09950-70010  (09951-07150)


Hide 4.INSTALL DIFFERENTIAL RING GEAR

a.

Clean the contact surfaces of the front differential case and differential ring gear.


b.

Heat the differential ring gear to approximately 100°C (212°F) in boiling water.


c.

Carefully take the differential ring gear out of the boiling water.


d.

After the moisture on the ring gear has completely evaporated, quickly set the differential ring gear onto the front differential case.


e.

Align the matchmarks on the differential ring gear and front differential case.


f.

Temporarily install 5 new lock plates and the 10 set bolts.


g.
C161293C01
0.719,1.344 1.083,1.76 false 1.083,1.76 0.76,1.281 false 1.115,1.75 1.844,1.896 0.729,0.146 10 false *a
*a Matchmark


After the differential ring gear cools down sufficiently, tighten the 10 bolts uniformly a little at a time.

Torque:
96.6 N*m (985 kgf*cm, 71 ft.*lbf)

HINT:

Tighten the bolts in diametrically opposite pairs.



h.
C161294N01
0.357,1.591 0.2,1.35 false 0.584,2.016 0.265,1.865 false 1.704,1.629 1.852,1.37 false 2.267,1.969 2.533,1.99 false 0.112,1.706 0.262,1.861 0.149,0.155 10 A 0.056,1.21 0.206,1.353 0.149,0.143 10 B 1.881,1.237 2.03,1.415 0.149,0.179 10 B 2.557,1.895 2.706,2.039 0.149,0.143 10 A

Using a chisel and hammer, stake the 5 lock plates.

HINT:

Strike the tab labeled A so that it is flush with the flat surface of the bolt. Strike the tab labeled B so that half of the tab contacts the bolt as shown in the illustration.



Hide 5.INSPECT RUNOUT OF RING GEAR

a.

Install the front differential case and 2 front differential case bearings (outer race) to the differential carrier, and install the 2 front differential bearing adjusting nuts so that there is no play in the bearing.


b.

Install the 2 bearing caps with the 4 bolts.

Torque:
85.3 N*m (870 kgf*cm, 63 ft.*lbf)


c.
C314650

Using a dial indicator, measure the runout of the differential ring gear.

Maximum runout:

0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the differential ring gear.


d.

Remove the 4 bolts, 2 bearing caps, 2 front differential bearing adjusting nuts and front differential case.


Hide 41211A 6.INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C161296N02
2.26,0.657 2.583,0.813 0.323,0.156 10 SST 1.791,0.726 2.227,0.726 false 2.227,0.726 1.761,1.192 false

Using SST and a press, press in the front drive pinion front tapered roller bearing (outer race).

SST
09316-60011  (09316-00011, 09316-00051)


Hide 41211B 7.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C162082N04
2.189,0.688 2.498,0.837 0.309,0.149 10 SST 1.722,0.769 2.16,0.769 false 2.153,0.775 1.702,1.069 false

Using SST and a press, press in the front drive pinion rear tapered roller bearing (outer race).

SST
09316-60011  (09316-00011, 09316-00021)


Hide 41211A 8.INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

a.

Install the front differential drive pinion plate washer onto the drive pinion.

HINT:

First fit a front differential drive pinion plate washer with the same thickness as the removed front differential drive pinion plate washer, and then check the tooth contact pattern. Replace the front differential drive pinion plate washer with one of a different thickness if necessary.



b.
C161297C01
2.833,1.083 2.656,1.083 2.656,1.083 2.25,1.354 false 0.667,0.875 0.667,1.594 false 2.854,1.01 3.156,1.156 0.302,0.146 10 false SST 0.604,1.615 1.469,1.781 0.865,0.167 10 false *1
*1 Front Differential Drive Pinion Plate Washer


Using SST and a press, press in the front drive pinion front tapered roller bearing (inner race).

SST
09506-30012  


Hide 9.ADJUST DIFFERENTIAL DRIVE PINION PRELOAD

a.
C311239

Install the differential drive pinion, front drive pinion front tapered roller bearing (inner race) and front differential drive pinion oil slinger.

HINT:

Install the front differential drive pinion bearing spacer and front differential carrier oil seal after adjusting the gear contact pattern.



b.
C237304C02
1.447,0.703 1.014,0.703 false 0.669,0.602 0.978,0.753 0.309,0.152 10 SST 2.736,1.239 2.901,1.4 0.166,0.161 10 *a 0.41,1.6 0.575,1.761 0.166,0.161 10 *b
*a Turn
*b Hold


Using SST, install the front drive pinion companion flange sub-assembly with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



c.

Adjust the drive pinion preload by tightening the front drive pinion companion flange nut.


d.
C282254C01
0.573,0.594 0.896,0.594 false 3.052,1.115 3.365,1.313 0.313,0.198 10 false *a 0.281,1.063 0.594,1.26 0.313,0.198 10 false *b 0.281,0.51 0.594,0.708 0.313,0.198 10 false SST
*a Turn
*b Hold


Using SST, hold the front drive pinion companion flange sub-assembly.

SST
09330-00021  (09330-00030)


e.

Using a 30 mm socket wrench and torque wrench, gradually tighten the front drive pinion companion flange nut within the adjustment range of the differential drive pinion preload.

Torque:
370 N*m (3773 kgf*cm, 273 ft.*lbf)

or less


NOTICE:
·

As there is no front differential drive pinion bearing spacer, tighten the front drive pinion companion flange front nut a little at a time. Be careful not to overtighten it.

·

Apply hypoid gear oil LSD to the drive pinion threads and front drive pinion companion flange nut seat face.




f.
C237317

Using a torque wrench, measure the preload.

Standard Preload (At Starting):
Item Specified Condition
New 1.05 to 1.64 N*m (11 to 16 kgf*cm, 10 to 14 in.*lbf)
Reused 0.56 to 0.85 N*m (6 to 8 kgf*cm, 5 to 7 in.*lbf)


NOTICE:
·

For a more accurate measurement, rotate the bearing forward and backward several times before measuring.

·

Record the differential drive pinion preload for the total preload measurement.




Hide 41311 10.INSTALL FRONT DIFFERENTIAL CASE

a.
C237353C02
0,0 0,0 false
V100135

MP grease


Apply MP grease to the rack of the front differential lock shift fork and connecting part of the No. 4 transfer indicator switch.


b.

Insert the front differential lock shift fork into the differential carrier as shown in the illustration.


c.
C161304

Place the front differential case bearing (outer race) and front differential bearing adjusting nut on the left side of the front differential lock sleeve.

HINT:

Check that the front differential lock sleeve moves smoothly.



d.
C161276

Insert the front differential lock shift fork into the groove of the front differential lock sleeve while holding the front differential lock sleeve by hand, and install the case onto the differential carrier.

HINT:

Make sure that there is backlash between the ring gear and drive pinion.



Hide 41315A 11.INSTALL FRONT DIFFERENTIAL BEARING ADJUSTING NUT

a.
C161855

Install the 2 front differential bearing adjusting nuts onto the differential carrier, making sure the nuts are threaded properly.


Hide 12.INSPECT AND ADJUST DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH

a.
C161856C02
1.115,1.469 0.615,1.677 0.615,1.677 1.073,1.323 true 0.448,1.594 1.177,1.74 0.729,0.146 10 false *a
*a Matchmark


Align the matchmarks on the bearing caps and differential carrier.


b.
C161857

Tighten the 4 bolts.

Torque:
85.3 N*m (870 kgf*cm, 63 ft.*lbf)


c.
C236337N03
2.25,0.833 2.583,0.646 2.583,0.646 2.865,0.646 true 2.906,0.594 3.365,0.792 0.458,0.198 10 false SST

Loosen the 4 bolts to the point where the front differential bearing adjusting nuts can be turned by SST.

SST
09960-10010  (09962-01000, 09963-00700)


d.

Using SST, tighten the adjusting nut on the ring gear side until the ring gear has a backlash of about 0.2 mm (0.00787 in.).


e.
C161859N03
1.896,1.458 2.76,0.76 true 2.802,0.635 3.125,0.781 0.323,0.146 10 false SST

While turning the ring gear, use SST to tighten the front differential bearing adjusting nut on the drive pinion side. After the bearings are settled, loosen the front differential bearing adjusting nut on the drive pinion side.

SST
09504-00011  


f.
C314651N01
2.583,0.927 2.729,0.646 2.729,0.646 2.875,0.646 false 2.927,0.573 3.385,0.771 0.458,0.198 10 false SST

Place a dial indicator on the top of the front differential bearing adjusting nut on the ring gear side.


g.

Adjust the side bearing to zero preload by tightening the other adjusting nut until the pointer on the indicator begins to move.


h.
C161859N03
1.896,1.458 2.76,0.76 true 2.802,0.635 3.125,0.781 0.323,0.146 10 false SST

Using SST, tighten the front differential bearing adjusting nut 1 to 1.5 notches from the zero preload position.


i.
C236331N03
1.792,1.354 2.406,0.542 2.406,0.542 2.698,0.542 true 2.76,0.479 3.219,0.677 0.458,0.198 10 false SST

Using a dial indicator, adjust the ring gear backlash until it is within the specification.

Standard backlash:

0.13 to 0.18 mm (0.00512 to 0.00708 in.)


HINT:

The backlash is adjusted by turning the left and right adjusting nuts by an equal amount. For example, loosen the nut on the left side 1 notch and tighten the nut on the right side 1 notch.



j.
C161857

Tighten the 4 bearing cap bolts.

Torque:
85.3 N*m (870 kgf*cm, 63 ft.*lbf)


k.

After rotating the ring gear 5 turns or more, recheck the ring gear backlash.

Standard backlash:

0.13 to 0.18 mm (0.00512 to 0.00708 in.)



Hide 13.INSPECT TOTAL PRELOAD

a.
C161259

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard total preload (at starting):

0.46 to 0.66 N*m (4.7 to 6.7 kgf*cm, 4.1 to 5.8 in.*lbf) + Drive pinion preload


HINT:

Record the differential ring gear preload.



Hide 14.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

a.
C311263

Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.


b.

Turn the companion flange in both directions to inspect the ring gear for proper tooth contact.

C247128C02
0.313,0.927 0.625,1.125 0.313,0.198 10 *a 2.563,0.083 2.875,0.281 0.313,0.198 10 *b 4.844,0.063 5.156,0.26 0.313,0.198 10 *c 3.667,1.479 3.979,1.677 0.313,0.198 10 *d 2.656,1.99 2.969,2.188 0.313,0.198 10 *e 4.875,2.042 5.188,2.24 0.313,0.198 10 *f 3.708,3.281 4.021,3.479 0.313,0.198 10 *g
*a Proper Contact *b Heel Contact
*c Face Contact *d Select an adjusting washer that will shift the drive pinion closer to the ring gear (*b, *c)
*e Toe Contact *f Flank Contact
*g Select an adjusting washer that will shift the drive pinion away from the ring gear (*e, *f) - -



c.
C161315C01
1.667,1.292 1.667,1.656 false 1.594,1.677 2.448,1.844 0.854,0.167 10 false *1
*1 Front Differential Drive Pinion Plate Washer


Inspect the tooth contact pattern.

If the teeth are not contacting properly, use the following table to select a proper washer for correction.

Standard Plate Washer Thickness:
Thickness Thickness
1.69 to 1.71 mm (0.0666 to 0.0673 in.) 2.02 to 2.04 mm (0.0796 to 0.0803 in.)
1.72 to 1.74 mm (0.0678 to 0.0685 in.) 2.05 to 2.07 mm (0.0808 to 0.0814 in.)
1.75 to 1.77 mm (0.0689 to 0.0696 in.) 2.08 to 2.10 mm (0.0819 to 0.0826 in.)
1.78 to 1.80 mm (0.0701 to 0.0708 in.) 2.11 to 2.13 mm (0.0831 to 0.0838 in.)
1.81 to 1.83 mm (0.0713 to 0.0720 in.) 2.14 to 2.16 mm (0.0843 to 0.0850 in.)
1.84 to 1.86 mm (0.0725 to 0.0732 in.) 2.17 to 2.19 mm (0.0855 to 0.0862 in.)
1.87 to 1.89 mm (0.0737 to 0.0744 in.) 2.20 to 2.22 mm (0.0867 to 0.0874 in.)
1.90 to 1.92 mm (0.0749 to 0.0755 in.) 2.23 to 2.25 mm (0.0878 to 0.0885 in.)
1.93 to 1.95 mm (0.0760 to 0.0767 in.) 2.26 to 2.28 mm (0.0890 to 0.0897 in.)
1.96 to 1.98 mm (0.0772 to 0.0779 in.) 2.29 to 2.31 mm (0.0902 to 0.0909 in.)
1.99 to 2.01 mm (0.0784 to 0.0791 in.) 2.32 to 2.34 mm (0.0914 to 0.0921 in.)



Hide 41204E 15.REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT

Hide 41204D 16.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 41211A 17.REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

Hide 41231F 18.INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER

Hide 41115F 19.INSTALL FRONT DIFFERENTIAL OIL STORAGE RING

Hide 41211B 20.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

Hide 41214C 21.INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41101D 22.INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL

Hide 41204D 23.INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 25.INSPECT TOTAL PRELOAD

a.
C161259

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard total preload (at starting):

0.46 to 0.66 N*m (4.7 to 6.7 kgf*cm, 4.1 to 5.8 in.*lbf) + Drive pinion preload


If necessary, disassemble and inspect the differential.


Hide 41204D 27.INSPECT RUNOUT OF FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

Hide 41204E 28.STAKE FRONT DRIVE PINION COMPANION FLANGE NUT

Hide 41316A 29.INSTALL FRONT DIFFERENTIAL BEARING ADJUSTING NUT LOCK

a.
C161917

Install 2 new front differential bearing adjusting nut locks onto the 2 bearing caps with the 2 bolts.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


b.

Bend the nut locks.


Hide 41462 30.INSTALL FRONT DIFFERENTIAL LOCK SHIFT FORK SHAFT

a.

Apply MP grease to the outer circuit of the front differential lock shift fork shaft.


b.
C161320C01
0.594,1.375 0.76,1.729 0.76,1.729 1.167,0.99 true 0.771,1.292 0.656,1.042 0.656,1.042 0.49,1.042 true 0.677,1.76 1.063,1.906 0.385,0.146 10 false *b 0.292,0.969 0.781,1.115 0.49,0.146 10 false *a
*a Groove
*b Hole


Install the front differential lock shift fork shaft to match the hole of the front differential lock shift fork and that of the front differential lock shift fork shaft.


c.

Remove any FIPG material and be careful not to drop oil on the contact surface of the differential carrier and differential lock shaft retainer.


d.
C121506C01
1.552,0.885 1.281,0.552 1.281,0.552 1.031,0.552 true 0.865,0.469 1.365,0.74 0.5,0.271 10 false *a
*a Seal Packing Diameter: 1 to 2 mm (0.0394 to 0.0787 in.)


Apply seal packing to the differential carrier as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


HINT:

Install the differential lock shaft retainer within 10 minutes after applying seal packing.



e.

Clean the threads of the bolts and retainer bolts holes with toluene or trichloroethylene.


f.
C161322

Apply adhesive to 2 or 3 threads of the mounting bolt ends.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



g.

Install the differential lock shaft retainer with the 2 bolts.

Torque:
23.5 N*m (240 kgf*cm, 17 ft.*lbf)


h.
C161323

Using a 5 mm pin punch and hammer, tap in the slotted spring pin to the front differential lock shift fork.


i.
C161324C01
0.49,1.688 0.792,1.917 0.302,0.229 10 false *a
*a Lock


Shift the fork to the lock side.


j.
C237466C01
1.865,0.646 1.865,0.802 false 2.156,0.646 2.385,0.531 2.385,0.531 2.615,0.531 false 2.583,0.823 2.771,0.76 2.771,0.76 2.927,0.76 false 2.885,1.208 2.885,1.271 2.885,1.271 2.583,1.271 false 0.698,2.313 0.698,0.792 0.698,0.792 0.583,0.792 true 1.781,0.802 1.938,0.948 0.156,0.146 10 false *1 2.635,0.438 2.792,0.583 0.156,0.146 10 false *2 2.948,0.667 3.104,0.813 0.156,0.146 10 false *3 2.396,1.177 2.552,1.323 0.156,0.146 10 false *4 0.396,0.708 0.552,0.854 0.156,0.146 10 false *4
*1 Steel Ball
*2 Compression Spring
*3 Spring Seat
*4 Screw Plug


Install the steel ball, compression spring and spring seat.


k.

Clean the threads of the 2 plug holes with toluene or trichloroethylene.


l.

Apply adhesive to the plug threads.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



m.

Using a 6 mm hexagon wrench, install the 2 screw plugs.

Torque:
21.6 N*m (220 kgf*cm, 16 ft.*lbf)


Hide 41453A 31.INSPECT FRONT DIFFERENTIAL LOCK SLEEVE

a.
C161326

Measure the distance between the front differential lock sleeve and tip of the front differential case when the differential is free and locked, respectively.

Standard Distance:
Position Specified Condition
Lock 17.44 to 18.86 mm (0.687 to 0.742 in.)
Free 32.40 to 33.90 mm (1.276 to 1.334 in.)



Hide 41450A 33.INSTALL NO. 2 DIFFERENTIAL LOCK SHIFT ACTUATOR

a.
C237468C01
0.979,0.927 1.667,0.24 1.667,0.24 2.208,0.24 true 1.208,1.75 2.177,1.75 true 2.25,0.146 2.531,0.333 0.281,0.188 10 false *1 2.208,1.656 2.521,1.823 0.313,0.167 10 false *2
*1 Shift Fork
*2 Actuator Installation Hole
V100135

Outside


Check that the outermost rack tooth of the shift fork is almost directly above the center line of the No. 2 differential lock shift actuator installation hole.


b.
C313148C01
1.833,3.51 2.135,3.208 2.135,3.208 2.354,3.208 false 2.385,3.104 2.698,3.302 0.313,0.198 10 false *a 1.875,2.552 2.188,2.75 0.313,0.198 10 false *b 1.094,3 1.406,3.198 0.313,0.198 10 false *c 2.813,0.635 3.125,0.833 0.313,0.198 10 false *d 2.823,1.375 3.135,1.573 0.313,0.198 10 false *e
*a Matchmark
*b 5°+/-3
*c 95.5°
*d 1.5 V (for 12 V Battery)
*e 3.0 V (for 24 V Battery)


Check that the matchmarks on the pinion of the No. 2 differential lock shift actuator are in the range between 2 and 8° clockwise of the center line of the No. 2 differential lock shift actuator.

NOTICE:
·

If the matchmarks are not within the specified range, use dry cell batteries to rotate the pinion until the matchmarks are within the range.

·

Do not apply positive (+) battery voltage directly between terminals.

·

If the matchmarks come to the limit of the rotation range, do not apply any more voltage.




c.
C161329

Install a new O-ring to the No. 2 differential lock shift actuator.


d.

Apply a light coat of gear oil to the O-ring.


e.

Apply MP grease to the gear parts.


f.
C237470C01
0.823,0.449 0.918,0.449 0.918,0.449 0.918,0.61 false 0.84,0.606 1.001,0.761 0.161,0.155 10 *1
*1 Knock Pin


Check that the outermost rack tooth of the shift fork aligns with the matchmarks on the pinion of the No. 2 differential lock shift actuator.


g.

Install the No. 2 differential lock shift actuator so that the long hole in the actuator fits with the knock pin on the front differential carrier assembly.

HINT:

Do not damage the O-ring of the No. 2 differential lock shift actuator.



h.

Rotate the actuator counterclockwise so that the knock pin slides to the end of the hole as shown in the illustration.


i.

Install the bolt.

Torque:
26.5 N*m (270 kgf*cm, 20 ft.*lbf)