Home › Brake › PARKING BRAKE › PARKING BRAKE SYSTEM
RM25T0E _54 Brake _029919 PARKING BRAKE _0138072 PARKING BRAKE SYSTEM N

PARKING BRAKE  PARKING BRAKE SYSTEM  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT PARKING BRAKE LEVER TRAVEL

a.

Fully pull the parking brake lever to engage the parking brake.


b.

Release the lever to disengage the parking brake.


c.

Slowly pull the parking brake lever all the way and count the number of clicks.

Standard parking brake lever travel when pulled with a force of 196 N (20 kgf, 44 lbf):

7 to 9 clicks


If the parking brake lever travel is not as specified, adjust the parking brake shoe clearance and parking brake lever travel.


Hide 2.REMOVE REAR WHEEL

Hide 58901A 3.REMOVE REAR CONSOLE BOX SUB-ASSEMBLY

Hide 46243 4.REMOVE PARKING BRAKE LEVER COVER

Hide 5.ADJUST PARKING BRAKE LEVER TRAVEL (for Disc Type)

a.

Completely release the parking brake lever.


b.
C304594C01
1.646,0.927 1.656,0.344 1.656,0.344 1.302,0.344 false 0.75,1.021 1.583,1.021 false 1.146,0.26 1.458,0.458 0.313,0.198 10 false *1 0.573,0.938 0.885,1.135 0.313,0.198 10 false *2
*1 Lock Nut
*2 Adjusting Nut


Loosen the lock nut and adjusting nut to completely release the parking brake cable.


c.

Temporarily install the hub nuts.


d.

Remove the hole plug.


e.
C304595C01
1.76,0.802 1.99,0.771 false
V100135

Shoe Adjuster Contracts
V100136

Shoe Adjuster Expands


Turn the shoe adjuster so that it expands until the disc locks.


f.

Turn the shoe adjuster so that it contracts until the disc can rotate smoothly.

OK:

8 notches



g.

Check that there is no brake drag against the shoe.


h.

Install the hole plug.


i.

Remove the hub nuts.


j.
C304596C01
0.063,0.917 0.219,1.115 0.156,0.198 10 false A
V100135

Pull


Lightly pull the bell crank.


k.

Check that there is no looseness in the parking brake cable.


l.

Adjust the gap between the stopper bolt and the backing plate.

Gap A:

0.5 to 0.9 mm (0.0197 to 0.0354 in.)



m.

Lock the adjust bolt with the lock nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


n.

Turn the adjusting nut until the parking brake lever travel becomes correct.

Standard parking brake lever travel when pulled with a force of 196 N (20 kgf, 44 lbf):

7 to 9 clicks



o.

Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


p.

Operate the parking brake lever 3 to 4 times and check the parking brake lever travel.

Standard parking brake lever travel when pulled with a force of 196 N (20 kgf, 44 lbf):

7 to 9 clicks



q.

Check whether the parking brake drags or not.


r.

When operating the parking brake lever, check that the brake warning light comes on.

Standard Condition:

The brake warning light always illuminates at the first click.



Hide 6.INSTALL PARKING BRAKE LEVER TRAVEL (for Drum Type)

a.

Completely release the parking brake lever.


b.
C304594C01
1.646,0.927 1.656,0.344 1.656,0.344 1.302,0.344 false 0.75,1.021 1.583,1.021 false 1.146,0.26 1.458,0.458 0.313,0.198 10 false *1 0.573,0.938 0.885,1.135 0.313,0.198 10 false *2
*1 Lock Nut
*2 Adjusting Nut


Loosen the lock nut and adjusting nut to completely release the parking brake cable.


c.

Temporarily install the hub nuts.


d.

Remove the hole plug.


e.
C151749C09
0,0 0,0 false
V100135

Expand


Turn the adjuster to expand the shoe until the drum locks.


f.
C233134C15
2.073,0.594 1.844,0.594 1.844,0.594 1.531,1 false 2.083,0.5 2.24,0.656 0.156,0.156 10 false *1
*1 Automatic Adjust Lever
V100135

Contract


Hold the automatic adjust lever away the adjuster, and contract the brake shoe by turning the adjust bolt using another screwdriver until the drum can rotate smoothly.


g.
C304597C01
0.24,1 0.396,1.198 0.156,0.198 10 false A
V100135

Pull


Lightly pull the bell crank.


h.

Check that there is no looseness in the parking brake cable.


i.

Adjust the gap between the stopper bolt and the backing plate.

Gap A:

0.5 to 0.9 mm (0.0197 to 0.0354 in.)



j.

Lock the adjust bolt with the lock nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


k.

Install the hole plug.


l.

Remove the hub nuts.


m.

Turn the adjusting nut until the parking brake lever travel becomes correct.

Standard parking brake lever travel when pulled with a force of 196 N (20 kgf, 44 lbf):

7 to 9 clicks



n.

Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


o.

Operate the parking brake lever 3 to 4 times and check the parking brake lever travel.

Standard parking brake lever travel when pulled with a force of 196 N (20 kgf, 44 lbf):

7 to 9 clicks



p.

Check whether the parking brake drags or not.


q.

When operating the parking brake lever, check that the brake warning light comes on.

Standard Condition:

The brake warning light always illuminates at the first click.



Hide 46243 7.INSTALL PARKING BRAKE LEVER COVER

Hide 58901A 8.INSTALL REAR CONSOLE BOX SUB-ASSEMBLY