Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2016.08
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0138307 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located on the combination meter assembly. When the ignition switch is turned from off to ON, the SRS warning light illuminates. If the SRS is normal, the SRS warning light turns off automatically after approximately 6 seconds. If there is a malfunction in the SRS, the SRS warning light remains illuminated even after approximately 6 seconds have passed. When terminals TC and CG of the DLC3 are connected, the DTCs are communicated through SRS warning light blinking patterns.

WIRING DIAGRAM

C315265E01
0.219,3.271 1.104,3.927 0.885,0.656 10 false from Battery 5.51,5.906 7.135,6.469 1.625,0.563 10 false Airbag Sensor Assembly 2.792,5.719 4.781,6.302 1.99,0.583 10 false Combination Meter Assembly 5.51,5.729 5.969,5.927 0.458,0.198 10 false I51 4.125,2.26 4.583,2.458 0.458,0.198 10 false L26 2.802,2.667 3.26,2.865 0.458,0.198 10 false L25 2.802,3.26 3.26,3.458 0.458,0.198 10 false L25 2.802,4.25 3.26,4.448 0.458,0.198 10 false L25 3.146,2.677 3.604,2.875 0.458,0.198 10 false B 3.167,3.271 3.625,3.469 0.458,0.198 10 false B 3.146,4.271 3.604,4.469 0.458,0.198 10 false ES 3.823,2.25 4.281,2.448 0.458,0.198 10 false A/B 6.156,2.271 6.615,2.469 0.458,0.198 10 false LA 6.146,3.656 6.604,3.854 0.458,0.198 10 false E1 6.146,4.292 6.604,4.49 0.458,0.198 10 false E2 5.875,4.177 6.333,4.375 0.458,0.198 10 false 26 5.865,3.583 6.323,3.781 0.458,0.198 10 false 25 5.906,2.188 6.365,2.385 0.458,0.198 10 false 11 5.896,0.771 6.354,0.969 0.458,0.198 10 false 21 6.135,0.896 6.594,1.094 0.458,0.198 10 false IG2 2.115,1.042 2.573,1.24 0.458,0.198 10 false IGN 2.115,2.823 2.573,3.021 0.458,0.198 10 false MET 1.875,3.438 2.75,3.792 0.875,0.354 10 false DOME NO.1 0.188,0.813 0.958,1.417 0.771,0.604 10 false from Ignition Switch 4.146,2.073 4.594,2.302 0.448,0.229 10 false 19 2.813,2.469 3.26,2.698 0.448,0.229 10 false 28 2.813,3.083 3.26,3.313 0.448,0.229 10 false 26 2.854,4.063 3.302,4.292 0.448,0.229 10 false 15

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK BATTERY
a.

Measure the voltage of the battery.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTION OF CONNECTOR

NG

RECHARGE OR REPLACE BATTERY

2.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and combination meter assembly.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

CONNECT CONNECTORS PROPERLY

3.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the connector from the airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


C198548C31
0.417,0.729 0.833,0.979 0.417,0.25 1.24,1.906 1.583,1.375 true 2.063,1.865 1.729,1.375 true 2.198,1.354 2.615,1.354 true 1.552,0.281 1.875,0.583 0.323,0.302 10 false *a 0.5,0.781 0.938,1.104 0.438,0.323 10 false I51 1.052,1.875 1.417,2.167 0.365,0.292 10 false E2 2.104,1.875 2.427,2.177 0.323,0.302 10 false E1 2.677,1.271 3,1.573 0.323,0.302 10 false IG2
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I51-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I51-25 (E1) - Body ground Always Below 1 Ω
I51-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPLACE HARNESS AND CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the connector from the combination meter assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


C212427C04
1.542,0.677 1.906,0.948 0.365,0.271 0.531,1.927 0.698,1.927 0.698,1.927 1.031,1.656 true 2.594,2.031 2.406,2.031 2.406,2.031 2.219,1.677 true 2.74,1.865 2.552,1.865 2.552,1.865 2.417,1.656 true 0.125,0.208 0.438,0.365 0.313,0.156 10 false *a 1.594,0.729 1.906,0.885 0.313,0.156 10 false L25 2.635,1.948 2.948,2.104 0.313,0.156 10 false B 0.26,1.854 0.573,2.01 0.313,0.156 10 false ES 2.76,1.802 3.073,1.958 0.313,0.156 10 false B
*a Front view of wire harness connector
(to Combination Meter Assembly)


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L25-28 (B) - Body ground Ignition switch ON 11 to 14 V
L25-26 (B) - Body ground Always 11 to 14 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L25-15 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - COMBINATION METER ASSEMBLY)
a.
C212446C04
0.448,3.74 0.896,3.969 0.448,0.229 0.458,1.177 0.906,1.406 0.448,0.229 0.948,4.427 1.844,4.281 true 2.188,1.427 2.427,1.615 2.427,1.615 2.594,1.615 true 0.365,0.26 0.677,0.417 0.313,0.156 10 false *a 0.469,3.104 0.781,3.26 0.313,0.156 10 false *b 2.656,1.531 2.969,1.688 0.313,0.156 10 false LA 0.688,4.354 1.271,4.51 0.583,0.156 10 false A/B 0.531,3.781 1.115,3.938 0.583,0.156 10 false L26 0.542,1.219 1.125,1.375 0.583,0.156 10 false I51
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I51-11 (LA) - L26-19 (A/B) Always Below 1 Ω
I51-11 (LA) - Body ground Always 10 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK COMBINATION METER ASSEMBLY

NG

REPLACE HARNESS AND CONNECTOR

6.CHECK COMBINATION METER ASSEMBLY
a.

Connect the connector to the combination meter assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 second.


c.

Turn the ignition switch to ON.


d.
C198548C32
0.417,0.719 0.833,0.969 0.417,0.25 2.188,1.167 2.51,1.479 2.51,1.479 2.698,1.479 true 1.552,0.281 1.875,0.583 0.323,0.302 10 false *a 0.49,0.771 0.813,1.073 0.323,0.302 10 false I51 2.75,1.406 3.073,1.708 0.323,0.302 10 false LA
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I51-11 (LA) - Body ground Ignition switch ON 11 to 14 V



e.

Turn the ignition switch to OFF.


Result:
Proceed to
OK
NG



OK

7.CHECK SRS WARNING LIGHT (SHORT TO GROUND)

NG

REPLACE COMBINATION METER ASSEMBLY

7.CHECK SRS WARNING LIGHT (SHORT TO GROUND)
a.

Turn the ignition switch to ON.


b.

Check the SRS warning light condition.

NOTICE:

Make sure that nobody is in the vehicle.


OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.



Result:
Proceed to
OK
NG



OK

8.REPLACE AIRBAG SENSOR ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

8.REPLACE AIRBAG SENSOR ASSEMBLY
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.



d.

Check the SRS warning light condition.

OK:

SRS warning light illuminates normally.



Result:
Proceed to
OK
NG



OK

END (AIRBAG SENSOR ASSEMBLY IS DEFECTIVE)

NG

REPLACE COMBINATION METER ASSEMBLY