Home › Drivetrain › HF1A (TRANSFER / 4WD / AWD) › TRANSFER CASE REAR OIL SEAL
RM25T0E _52 Drivetrain _029904 HF1A TRANSFER / 4WD / AWD _0138378 TRANSFER CASE REAR OIL SEAL A

HF1A TRANSFER / 4WD / AWD  TRANSFER CASE REAR OIL SEAL  REPLACEMENT  


PROCEDURE

Hide 37110 2.REMOVE PROPELLER SHAFT ASSEMBLY

Hide 33309 3.REMOVE TRANSFER OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

a.
C271038

Using a chisel and hammer, loosen the staked part of the lock nut.

NOTICE:
·

Completely loosen the staked part of the nut when removing it.

·

Do not damage the threads of the output shaft assembly.




b.
C311874C01
2.5,1.885 2.302,1.885 2.302,1.885 2.125,1.552 true 2.479,0.25 2.792,0.448 0.313,0.198 10 false *a 1.865,1.927 2.177,2.125 0.313,0.198 10 false *b 2.594,1.813 3.063,2.073 0.469,0.26 10 false SST
*a Turn
*b Hold


Using SST to hold the transfer output shaft companion flange sub-assembly.

SST
09330-00021  


c.

Using a 30 mm socket wrench, remove the lock nut.


d.

Remove the transfer output shaft companion flange sub-assembly.

NOTICE:

Do not drop the transfer speedometer drive gear.



Hide 36109C 4.REMOVE OIL SEAL (REAR TRANSFER EXTENSION HOUSING SUB-ASSEMBLY)

a.
C311876N01
1.917,0.719 1.917,0.26 1.917,0.26 2.125,0.26 true 2.219,0.177 2.677,0.375 0.458,0.198 10 false SST

Using SST, remove the oil seal (rear transfer extension housing sub-assembly).

SST
09308-00010  

NOTICE:

Do not damage the oil seal and extension housing contact surface.



Hide 36109C 5.INSTALL OIL SEAL (REAR TRANSFER EXTENSION HOUSING SUB-ASSEMBLY)

C311877N01
0.823,0.75 1.365,0.281 1.365,0.281 1.073,0.76 true 1.448,0.177 1.906,0.375 0.458,0.198 10 false SST 1.667,3.021 2.125,3.219 0.458,0.198 10 false (A)

a.

Apply MP grease to the lip of a new oil seal (rear transfer extension housing sub-assembly).


b.

Using SST and a hammer, install the oil seal (rear transfer extension housing sub-assembly) as shown in the illustration.

SST
09502-12010  
09513-36040  

Drive in depth (A):

0 to 0.5 mm (0 to 0.0196 in.)


NOTICE:
·

Install the oil seal (rear transfer extension housing sub-assembly) so that its outer edge is positioned past the chamfered part of the rear transfer extension housing sub-assembly.

·

Do not to damage the oil seal (rear transfer extension housing sub-assembly).




Hide 33309 6.INSTALL TRANSFER OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

a.

Install the transfer output shaft companion flange sub-assembly with transfer speedometer drive gear.

NOTICE:

Do not drop the transfer speedometer drive gear.



b.

Install a new O-ring.

NOTICE:

Do not damage the O-ring.



c.
C311875C01
2.25,1.792 2.385,1.979 2.385,1.979 2.604,1.979 true 1.396,0.438 1.708,0.635 0.313,0.198 10 false *a 1.875,1.938 2.188,2.135 0.313,0.198 10 true *b 2.698,1.875 3.156,2.073 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST to hold the transfer output shaft companion flange sub-assembly, install a new lock nut.

SST
09330-00021  

Torque:
127.4 N*m (1299 kgf*cm, 94 ft.*lbf)


d.
C311878

Using a chisel and hammer, stake the lock nut in 2 locations.

NOTICE:
·

Securely stake the shaft to the lock nut groove.

·

Be careful not to damage the parts around the lock nut.

·

Do not apply excessive force to the shaft.




Hide 37110 7.INSTALL PROPELLER SHAFT ASSEMBLY

Hide 9. CHECK FOR TRANSFER OIL LEAK