Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2016.08–2022.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0100  Mass or Volume Air Flow Circuit  


DESCRIPTION

The mass air flow meter sub-assembly consists of a platinum hot wire, a temperature sensor and a control circuit installed in a plastic housing. The temperature sensor (located in the intake air by-pass of the housing) detects the intake air temperature.

There is little variation in the output from the mass air flow meter, as the output voltage is converted into a periodic signal which minimizes the effect of wire harness resistance.

The internal circuit of the mass air flow meter sub-assembly contains a hot wire and cold wire. A voltage is output through a bridge circuit (refer to the illustration) indicating the cooling of the hot wire according to the intake air amount. This voltage is then converted into a periodic signal by the periodic signal conversion circuit and output to the ECM. The frequency varies between approximately 250 to 11000 Hz depending on the air flow rate. The ECM calculates the mass air flow rate based on this frequency.

A207644E10
2.01,1.375 1.927,1.375 1.927,1.375 1.677,1.74 true 0.729,2.74 1.354,1.844 true 5.948,2.021 5.635,0.573 5.635,0.573 5.823,0.573 true 6.115,2.104 6.25,3.271 true 5.573,2.531 4.573,3.26 true 2.333,1.938 2.615,1.771 2.615,1.771 2.76,1.771 false 1.677,0.5 1.927,0.656 0.25,0.156 10 false +B 1.646,0.865 2.729,1.167 1.083,0.302 10 false Power Transistor 2.854,1.698 3.802,1.948 0.948,0.25 10 false Output Voltage 2.073,1.302 3.188,1.521 1.115,0.219 10 false Hot Wire Element 0.156,2.74 1.354,3.01 1.198,0.271 10 false Cold Wire Element 5.885,0.5 7,0.719 1.115,0.219 10 false Hot Wire Element 5.938,3.302 7.135,3.573 1.198,0.271 10 false Cold Wire Element 3.698,3.292 5.813,3.656 2.115,0.365 10 false Temperature Sensor (Thermistor) 2.219,2.344 3.417,2.667 1.198,0.323 10 false Periodic Signal Conversion Circuit 2.198,3.323 3.365,3.49 1.167,0.167 10 false Output Frequency

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0100 Mass or Volume Air Flow Circuit Mass air flow meter signal frequency is less than 850 Hz with the engine speed at 400 rpm or more for 3 seconds.
(1 trip detection logic)
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0100 MAF

HINT:

There is less air than the actual intake air amount, EGR is decreased according to the target EGR:

- Combustion noise worsens


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0100 3 seconds after engine is started

WIRING DIAGRAM

A394555E01
0.625,2.594 1.698,2.792 1.073,0.198 10 false Battery 0.458,1.792 1.531,1.99 1.073,0.198 10 false FL MAIN 0.76,0.625 1.833,0.823 1.073,0.198 10 false EFI MAIN2 1.906,1.396 2.979,1.594 1.073,0.198 10 false MAIN2 2.479,0.885 2.646,1.063 0.167,0.177 10 false 1 5.146,0.656 5.313,0.833 0.167,0.177 10 false 1 1.656,0.885 1.823,1.063 0.167,0.177 10 false 2 1.667,0.354 1.833,0.531 0.167,0.177 10 false 5 2.469,0.354 2.635,0.531 0.167,0.177 10 false 3 3.719,0.344 3.885,0.521 0.167,0.177 10 false 3 5.125,1.24 5.292,1.417 0.167,0.177 10 false 2 3.896,0.344 4.146,0.563 0.25,0.219 10 false +B 4.781,0.667 5.125,0.875 0.344,0.208 10 false VG 4.719,1.24 5.063,1.448 0.344,0.208 10 false E2G 3.521,1.844 5.813,2.094 2.292,0.25 10 false Mass Air Flow Meter Sub-assembly 3.51,1.667 3.854,1.875 0.344,0.208 10 false C41 5.719,0.76 6.063,0.969 0.344,0.208 10 false C39 5.729,1.323 6.073,1.531 0.344,0.208 10 false C39 5.719,2.885 6.063,3.094 0.344,0.208 10 false A29 5.76,2.688 6.104,2.896 0.344,0.208 10 false 44 5.75,1.125 6.094,1.333 0.344,0.208 10 false 94 5.75,0.573 6.094,0.781 0.344,0.208 10 false 71 6.365,3.448 6.708,3.656 0.344,0.208 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION

·

After replacing an fuel injector, the ECM needs registration.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (POWER SOURCE CIRCUIT)
a.
A148358C05
1.5,0.906 1.958,1.177 0.458,0.271 1.677,2.073 1.177,2.719 true 0.104,0.104 0.302,0.281 0.198,0.177 10 false *a 1.052,2.75 1.302,2.938 0.25,0.188 10 false +B 1.594,0.979 1.917,1.156 0.323,0.177 10 false C41
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)


Disconnect the mass air flow meter sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
C41-3 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - MAIN2 RELAY)
2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C41-1 (VG) - C39-71 (VG) Always Below 1 Ω
C41-2 (E2G) - C39-94 (EVG) Always Below 1 Ω
C41-1 (VG) or C39-71 (VG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER(w/ DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Start the engine and wait for 3 seconds or more.


d.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs.

Result:
Result Proceed to
P0100 is output A
No DTC is output B




A

5.REPLACE ECM

B

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Start the engine and wait for 3 seconds or more.


d.

Enter the following menus: Engine and ECT / Trouble Codes.


e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - MAIN2 RELAY)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Remove the MAIN2 relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C41-3 (+B) - MAIN2 relay terminal 3 Always Below 1 Ω
C41-3 (+B) or MAIN2 relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT MAIN2 RELAY

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.INSPECT MAIN2 RELAY

Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (MAIN2 RELAY - ECM)

NG

11.REPLACE MAIN2 RELAY
10.CHECK HARNESS AND CONNECTOR (MAIN2 RELAY - ECM)
a.

Remove the MAIN2 relay from the engine room relay block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
MAIN2 relay terminal 1 - A29-44 (MREL) Always Below 1 Ω
MAIN2 relay terminal 1 - A29-44 (MREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPLACE MAIN2 RELAY
a.

Replace the MAIN2 relay.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED