Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0115  Engine Coolant Temperature Circuit  P0117  Engine Coolant Temperature Circuit Low Input  P0118  Engine Coolant Temperature Circuit High Input  


DESCRIPTION

A thermistor is built into the Engine Coolant Temperature (ECT) sensor and it changes its resistance value according to the engine coolant temperature.

The structure of the sensor and connection to the ECM is the same as the intake air temperature sensor.

HINT:

If the ECM detects DTC P0117 or P0118, it operates the fail-safe function in which the ECT is assumed to be 113°C (235°F).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0115 Engine Coolant Temperature Circuit Open or short in engine coolant temperature (ECT) sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open or short in engine coolant temperature (ECT) sensor circuit

·

ECT sensor

·

ECM


Comes on DTC stored
P0117 Engine Coolant Temperature Circuit Low Input Short in ECT sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Short in ECT sensor circuit

·

ECT sensor

·

ECM


Comes on DTC stored
P0118 Engine Coolant Temperature Circuit High Input Open in ECT sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open in ECT sensor circuit

·

ECT sensor

·

ECM


Comes on DTC stored

HINT:

When DTC P0117 and/or P0118 is detected, check the engine coolant temperature by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Coolant Temp.


Reference:
Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0115
P0117
P0118
Ignition switch to ON for 0.5 seconds

WIRING DIAGRAM

A165735E26
0.646,2.51 1.052,2.688 0.406,0.177 10 false C116 0.646,2.656 2.938,2.823 2.292,0.167 10 false Engine Coolant Temperature Sensor 2.479,1.635 2.646,1.802 0.167,0.167 10 false 1 2.448,1.031 2.615,1.198 0.167,0.167 10 false 2 5.24,1.667 5.49,1.833 0.25,0.167 10 false 92 5.219,1.031 5.469,1.198 0.25,0.167 10 false 93 5.552,1.021 5.906,1.188 0.354,0.167 10 false THW 6.24,0.573 6.5,0.74 0.26,0.167 10 false 5 V 6.167,0.917 6.323,1.083 0.156,0.167 10 false R 5.979,2.656 6.333,2.823 0.354,0.167 10 false C39 5.979,2.823 6.333,2.99 0.354,0.167 10 false ECM 5.552,1.656 5.906,1.823 0.354,0.167 10 false E2 2.031,1.021 2.385,1.188 0.354,0.167 10 false THW 2.167,1.635 2.521,1.802 0.354,0.167 10 false E2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).


HINT:
·

If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

d.

Read the value.

Standard value:

75 to 90°C (167 to 194°F) with warm engine.


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
75 to 90°C (167 to 194°F) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or more.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A213406C44
0.74,3.5 1.167,3.76 0.427,0.26 0.26,2.771 0.573,2.969 0.313,0.198 10 false *a 0.667,0.333 0.979,0.531 0.313,0.198 10 false *1 2.531,0.313 2.844,0.51 0.313,0.198 10 false *2 2.406,1.25 2.896,1.5 0.49,0.25 10 false THW 2.417,1.698 2.969,1.958 0.552,0.26 10 false ETHW 0.781,3.542 1.313,3.719 0.531,0.177 10 false C116
*1 ECT Sensor
*2 ECM
*a Front view of wire harness connector
(to ECT Sensor)


Disconnect the engine coolant temperature sensor connector.


b.

Connect terminals 1 (E2) and 2 (THW) of the ECT sensor wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

f.

Read the value.

Standard value:

140°C (284°F) or higher



Result:
Proceed to
OK
NG



OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the ECT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C116-2 (THW) - C39-93 (THW) Always Below 1 Ω
C116-1 (E2) - C39-93 (E2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A166688C02
0.583,2.083 0.823,2.281 0.24,0.198 10 false *1 2.667,2.302 2.906,2.5 0.24,0.198 10 false *2 2.396,1.427 2.823,1.615 0.427,0.188 10 false THW 2.406,1.906 2.833,2.094 0.427,0.188 10 false E2
*1 ECT Sensor
*2 ECM


Disconnect the ECT sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

e.

Read the value.

Standard value:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ENGINE COOLANT TEMPERATURE SENSOR

NG

5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the ECT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C116-2 (THW) or C39-93 (THW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR