While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.
If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) for more than 20 seconds.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0617 | Starter Relay Circuit High | When positive (+B) battery voltage of 10.5 V or more applied to ECM, and conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic): (a) Vehicle speed is more than 20 km/h (12.4 mph) (b) Engine speed is more than 1000 rpm (c) STA signal is ON |
·
Starter relay circuit
·
Ignition switch
·
ECM |
Comes on | DTC stored |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0617 | Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more |
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to the problem symptoms table.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>PROBLEM SYMPTOMS TABLE
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the value displayed on the GTS when the ignition switch is turned to the ON or START position.
| Ignition Switch Condition | GTS Display (Starter Signal) |
| ON | OFF |
| START | ON |
| Proceed to |
| OK |
| NG |
OK
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>CHECK FOR INTERMITTENT PROBLEMS
NG
| *a | Component without harness connected (Ignition Switch) |
Disconnect the ignition switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 4 (AM1) - 3 (ST1) | LOCK | 10 kΩ or higher |
| 4 (AM1) - 3 (ST1) | START | Below 1 Ω |
| Proceed to |
| OK |
| NG |
NG
OK
Replace the ignition switch assembly.
Click hereEngine / Hybrid System>1VD-FTV (STARTING)>IGNITION SWITCH>REMOVAL
| Proceed to |
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the value displayed on the GTS when the ignition switch is turned to the ON or START position.
| Ignition Switch Condition | GTS Display (Starter Signal) |
| ON | OFF |
| START | ON |
| Proceed to |
| OK |
| NG |
NG
OK
Disconnect the ignition switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L21-3 (ST1) - A29-48 (STA) | Always | Below 1 Ω |
| L21-3 (ST1) or A29-48 (STA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on and start the engine.
Clear DTCs.
Drive the vehicle at more than 20 km/h (12.4 mph) for over 20 seconds.
Enter the following menus: Powertrain / Engine and ECT / Data List / Trouble Codes.
Read DTCs.
| Proceed to | Proceed to |
| P0617 is output | A |
| No DTC is output | B |
A
B