Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0107  Manifold Absolute Pressure / Barometric Pressure Circuit Low Input  P0108  Manifold Absolute Pressure / Barometric Pressure Circuit High Input  


DESCRIPTION

A006532E15
0.385,0.49 0.521,0.688 0.135,0.198 10 false V 0.188,0.813 0.573,1.01 0.385,0.198 10 false 3.586 0.188,1.885 0.594,2.083 0.406,0.198 10 false 0.386 1.021,2.302 1.208,2.469 0.188,0.167 10 false 40 2.313,2.302 2.594,2.469 0.281,0.167 10 false 320 2.885,2.052 3.229,2.406 0.344,0.354 10 false kPa (abs) 2.885,2.531 3.333,2.708 0.448,0.177 10 false mmHg 2.885,2.875 3.333,3.063 0.448,0.188 10 false (in.Hg) 2.271,2.667 2.74,3.031 0.469,0.365 10 false 2400 (94.5) 0.958,2.667 1.354,3.031 0.396,0.365 10 false 300 (11.8) 1.365,3.083 2.167,3.26 0.802,0.177 10 false Air Pressure

The manifold absolute pressure sensor detects the intake manifold pressure by using its built-in sensor unit. The ECM determines the basic injection duration and injection advance timing based on the voltage output by the manifold absolute pressure sensor.

The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa (0 mmHg, 0 in.Hg)). As a result the ECM controls the air fuel ratio at the proper level under any driving conditions, and fuel control accuracy is not influenced by fluctuations in the atmospheric pressure due to factors such as high altitude, etc.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input After engine is started, condition (a) continues for more than 0.5 seconds
(1 trip detection logic)
(a) Manifold absolute pressure sensor voltage is 0.1 V or less.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored
P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input After engine is started, condition (a) continues for more than 0.5 seconds
(1 trip detection logic)
(a) Manifold absolute pressure sensor voltage is 4.8 V or higher.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored

HINT:

When DTC P0107 or P0108 is detected, check the intake manifold pressure by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / MAP.


Reference
Intake Manifold Pressure Malfunction
Approximately 0 kPa
·

Open in VC circuit

·

Open in PIM circuit

·

Short in PIM circuit


250 kPa (1875 mmHg, 73.8 in.Hg) or higher Open in E2 circuit

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0107
P0108
2 seconds after engine is started, race engine for 1 second

WIRING DIAGRAM

A165731E87
0.583,2.021 1.042,2.219 0.458,0.198 10 false C101 0.583,2.188 2.823,2.365 2.24,0.177 10 false Manifold Absolute Pressure Sensor 6.052,2.021 6.354,2.198 0.302,0.177 10 false C39 6.052,2.188 6.479,2.365 0.427,0.177 10 false ECM 1.604,1.615 1.76,1.76 0.156,0.146 10 false E 1.479,1.063 1.76,1.208 0.281,0.146 10 false PIM 1.521,0.479 1.76,0.625 0.24,0.146 10 false VC 5.698,1.594 6.281,1.792 0.583,0.198 10 false EPIM 5.698,1.042 5.979,1.188 0.281,0.146 10 false PIM 5.698,0.469 6.125,0.615 0.427,0.146 10 false VCPM 1.844,0.375 1.969,0.552 0.125,0.177 10 false 3 1.844,0.927 1.969,1.104 0.125,0.177 10 false 2 1.844,1.479 1.969,1.656 0.125,0.177 10 false 1 5.344,0.365 5.594,0.542 0.25,0.177 10 false 66 5.344,0.938 5.604,1.115 0.26,0.177 10 false 67 5.281,1.469 5.594,1.656 0.313,0.188 10 false 112

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).


HINT:
·

If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (MANIFOLD ABSOLUTE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.

Powertrain > Engine and ECT > Data List
Tester Display
MAP
50003 234 4

d.

Read the value.

Standard:

Same value as the actual atmospheric pressure.



Result:
Proceed to
OK
NG



OK

2.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

3.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
2.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the GTS off.


e.

Turn the igniton switch to ON for 3 seconds and turn the GTS on.


f.

After the engine is started for 2 seconds, race the engine for 1 second.


g.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.

1.

Enter the following menus: Engine and ECT / Utility / All Readiness.

2.

Input DTC P0107 or P0108.

3.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, race the engine for 1 minute, and then idle the engine for 5 minutes.




Result:
Proceed to
NEXT



NEXT

END

3.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.
A311456C07
1.458,0.146 1.854,0.375 0.396,0.229 1.323,2.313 1.719,2.542 0.396,0.229 1.177,1.604 1.458,1.094 true 2.135,1.615 1.875,1.104 true 1.667,1.615 1.667,1.104 true 0.406,4.177 0.646,3.396 true 1.365,4.188 0.646,3.573 true 2.167,4.219 0.729,3.396 true 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 0.125,2.021 0.438,2.219 0.313,0.198 10 false *b 1.5,0.177 1.927,0.365 0.427,0.188 10 false C101 1.083,1.635 1.396,1.833 0.313,0.198 10 false E 1.583,1.646 1.896,1.844 0.313,0.198 10 false PIM 2.083,1.646 2.396,1.844 0.313,0.198 10 false VC 1.396,2.344 1.708,2.542 0.313,0.198 10 false C39 0.146,4.208 0.854,4.479 0.708,0.271 10 false 66 (VCPM) 1.99,4.229 2.646,4.563 0.656,0.333 10 false 112 (PIM) 1.177,4.219 1.958,4.458 0.781,0.24 10 false 67 (EPIM)
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)
*b Front view of wire harness connector
(to ECM)


Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C101-2 (PIM) - C39-67 (PIM) Always Below 1 Ω
C101-3 (VC) - C39-66 (VCPM) Always Below 1 Ω
C101-1 (E) - C39-112 (EPIM) Always Below 1 Ω
C101-2 (PIM) or C39-67 (PIM) - Body ground Always 10 kΩ or higher
C101-3 (VC) or C39-66 (VCPM) - Body ground Always 10 kΩ or higher
C101-1 (E) or C39-112 (EPIM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)
a.
A165732C03
1.521,1.135 1.938,1.427 0.417,0.292 1.052,2.615 1.469,2.198 true 2.271,2.646 1.948,2.208 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 1.573,1.208 1.969,1.406 0.396,0.198 10 false C101 0.969,2.667 1.177,2.854 0.208,0.188 10 false E 2.26,2.677 2.5,2.833 0.24,0.156 10 false VC
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


Disconnect the manifold absolute pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
C101-3 (VC) - C101-1 (E) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

5.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

7.REPLACE ECM
5.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Clear the DTC.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the GTS off.


e.

Start the engine.


f.

After the engine is started for 2 seconds, race the engine for 1 second.


g.

Turn the GTS on.


h.

Confirm that the DTC is not output again.


i.

Enter the following menus: Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

j.

Input DTC P0107 or P0108.


k.

Check the DTC judgment result.

Result:
Result Proceed to
ABNORMAL A
NORMAL B


HINT:

If STATUS is INCOMPLETE or N/A, race the engine for 1 minute, and then idle the engine for 5 minutes.




A

7.REPLACE ECM

B

END

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

2.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

2.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED