Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P042E  Exhaust Gas Recirculation "A" Control Stuck Open  


DESCRIPTION

The EGR system recirculates exhaust gases. The recirculated gas mingles with the intake air so that the EGR system can slow the combustion speed and keep the combustion temperature down. This helps reduce NOx emissions.

In order to increase EGR circulation efficiency, the ECM adjusts the EGR valve lift amount and the throttle valve angle.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P042E Exhaust Gas Recirculation "A" Control Stuck Open Either of the following conditions is met (1 trip detection logic):
·

The target and actual positions of the EGR valve are different for 20 seconds or more.

·

While the engine is running, the EGR activation duty exceeds the threshold for 0.5 seconds a certain number of times (40 seconds or more).


·

EGR valve stuck

·

EGR valve does not move smoothly

·

EGR valve deposit

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P042E
·

MAF

·

MAP

·

EGR Close Lrn. Val.

·

Target EGR Valve Pos

·

Actual EGR Valve Pos



HINT:
·

Actual EGR valve opening percentage: Fully closed = 0%, fully open = 100%.

·

If DTC P042E is stored, the following symptoms may appear:

-

Stuck closed malfunction

*

Lack of power: due to fail-safe operation

*

Intake booming noise

*

Slight combustion noise



-

Stuck open malfunction

*

Black smoke

*

Lack of power

*

Vibration at engine stop

*

Misfire

*

White smoke

*

Engine stall





CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P042E After warming up engine and idling for 60 seconds, maintain engine speed at 2500 rpm for 40 seconds, drive vehicle, and perform engine brake deceleration by fully releasing accelerator when engine speed is 2000 rpm or more.

MONITOR DESCRIPTION

When the target and actual positions of the EGR valve are different, the ECM interprets this as a malfunction of the electric EGR control valve assembly and illuminates the MIL (1 trip detection logic).

A208465E14
3.896,2.719 4.094,2.417 4.094,2.417 4.208,2.417 true 5.292,3 5.104,2.875 5.104,2.875 4.948,2.875 true 3.865,3.49 4,3.615 4,3.615 4.125,3.615 true 4.833,4.573 4.885,4.833 4.885,4.833 5,4.833 true 3.781,4.396 3.906,4.396 false 3.906,4.396 3.99,4.552 true 0.063,0.031 3.26,0.229 3.198,0.198 10 false Electric EGR Control Valve Assembly Malfunction: 0.469,1.573 1.74,1.906 1.271,0.333 10 false EGR Valve Opening Position (Target) 0.375,3.375 1.74,3.552 1.365,0.177 10 false EGR Valve Condition 0.458,5.094 1.74,5.271 1.281,0.177 10 false Malfunction Counter 3.531,5.552 3.885,5.729 0.354,0.177 10 false Time 5.042,4.75 6.604,4.927 1.563,0.177 10 false Stores P042E 3.135,4.302 3.792,4.469 0.656,0.167 10 false Threshold 6.146,0.896 6.542,1.052 0.396,0.156 10 false Open 6.146,1.677 6.542,1.833 0.396,0.156 10 false Close 6.146,2.615 6.542,2.771 0.396,0.156 10 false Open 6.146,3.396 6.542,3.552 0.396,0.156 10 false Close 4.24,2.333 4.76,2.49 0.521,0.156 10 false Normal 2.635,2.771 4.906,2.927 2.271,0.156 10 false Abnormal (Does not move smoothly) 4.177,3.531 4.833,3.875 0.656,0.344 10 false Abnormal (Stuck)

HINT:
·

If a large amount of carbon deposits exists in the electric EGR control valve assembly, the following parts possibly also have deposits inside: The intake manifold, EGR cooler, exhaust fuel addition injector assemblies (if equipped), exhaust pipe assemblies (DPF catalytic converter), and other parts related to the exhaust gas.

·

Be sure to carefully examine "Actual EGR Valve Pos", "Target EGR Valve Pos" and "MAF" in the freeze frame data.

·

Be sure to carefully examine "Actual EGR Valve Pos #2", "Target EGR Valve Pos #2" and "MAF" in the freeze frame data.



CAUTION / NOTICE / HINT

NOTICE:
·

When cleaning the electric EGR control valve assembly or diesel throttle body assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in solvent may damage the parts.

·

After replacing the fuel supply pump assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION

·

After replacing an fuel injector, the ECM needs registration.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P042E)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
P042E is output A
P042E and other DTCs are output B


HINT:

If any DTCs other than P042E are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / Target EGR Valve Pos and Actual EGR Valve Pos

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Target EGR Valve Pos
Actual EGR Valve Pos
50004 234 95 821,822

e.

When changing the Active Test value for 1, 30, 60, 90, 60, 30 and 1%, check that Actual EGR Valve Pos smoothly changes to the set opening angle.

OK:

The Actual EGR Valve Pos value follows the Target EGR Valve Pos value.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

4.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
3.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Remove the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/ DPF)>REMOVAL


b.

Reconnect the electric EGR control valve assembly connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the EGR Step Position
50004 234 95

g.

Check if the valve of the electric EGR control valve assembly opens/closes when an Active Test is performed.

OK:

The valve opens/closes.



h.
A392189C01
2.771,3.229 2.865,2.552 2.865,2.552 2.948,2.552 true 2.615,3.844 2.99,4.417 2.99,4.417 3.073,4.417 true 0.99,3.167 0.99,2.521 0.99,2.521 1.073,2.521 true 2.99,2.49 3.302,2.688 0.313,0.198 10 false *1 3.115,4.323 3.427,4.521 0.313,0.198 10 false *1 1.115,2.448 1.427,2.646 0.313,0.198 10 false A 0.896,4.198 1.208,4.396 0.313,0.198 10 false *a 2.615,4.208 2.927,4.406 0.313,0.198 10 false *b
*1 Gap
*a OK
*b NG


Hold the electric EGR control valve assembly up to a light, and then from the side indicated by the arrow in the illustration, visually check that there is no gap between the valve and body.

OK:

No light passes through (there is no gap between the valve and body).


HINT:

Light passes through part A shown in the illustration even if the valve is completely closed as there is an opening in the seal ring of the valve. This is not a problem.


Result:
Result Proceed to
NG A
OK B


HINT:
·

If light passes through (there is a gap between the valve and body), replace the electric EGR control valve assembly.

·

Remove the deposits if there are many deposits in the electric EGR control valve assembly or the passage of the intake manifold.




i.

Reinstall the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/ DPF)>INSTALLATION



A

4.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY

B

5.CHECK FOR DEPOSIT
4.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/ DPF)>REMOVAL

HINT:

Before replacing the electric EGR control valve assembly, check the connections of the wire harness and connectors. If there is any abnormality, replace or repair the wire harness or connector.



Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK FOR DEPOSIT
a.

Remove the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/ DPF)>REMOVAL


b.

Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.

NOTICE:
·

When cleaning the electric EGR control valve, make sure the valve is completely closed.

·

Do not forcibly open the valve, as it may be damaged or deformed.

·

When cleaning the electric EGR control valve, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.

·

When cleaning the EGR control valve, care should be taken to prevent the ingress of cleaning solvent into the bearings of valve shaft, and when wiping off deposits on the EGR control valve, care should be taken not to push the deposits into the bearings of the valve shaft. These contaminants may adversely affect the function of the EGR control valve.



HINT:
·

If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.

·

If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power.




c.

Reinstall the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/ DPF)>INSTALLATION


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

After warming up the engine and idling for 60 seconds, maintain the engine speed at 2500 rpm for 40 seconds, drive the vehicle, and perform engine brake deceleration by fully the closing accelerator when the engine speed is 2000 rpm or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

i.

Confirm that the DTCs are not output again.


Result:
Proceed to
NEXT



NEXT

END