Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P062F  Internal Control Module EEPROM Error  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P062F Internal Control Module EEPROM Error When any condition below is met (1 trip detection logic):
·

Injector compensation code is not registered.

·

Wrong injector compensation code is registered.

·

Pilot quantity learning value is not registered.

·

Catalyst deterioration learning value is no tregistered.

·

Crank time compensation learning value is not registered.*

·

A/F sensor compensation learning value is not registered.*


*: When this malfunction occurs, the MIL does not illuminate.
·

Injector compensation code

·

Pilot quantity learning value

·

A/F sensor compensation learning value

·

Catalyst thermal deterioration value

·

Crank time compensation learning value

·

ECM


Comes on DTC stored

NOTICE:
·

When an fuel injector is replaced, the new injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.

·

Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each fuel injector. If an incorrect injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

·

When an fuel injector is replaced, perform pilot quantity learning. When the ECM is replaced, all of the existing pilot quantity learning values must be input into the new ECM.



HINT:

When replacing the ECM with a new one, if the injector compensation code, pilot quantity learning value and/or catalyst thermal deterioration value are not entered, DTC P062F will be stored.


When replacing the ECM with a new one, input all learning values and codes into the new ECM as follows:


a.

Prior to replacing the ECM, use the GTS to read and save each learning value and code from the original ECM.


b.

After installing a new ECM, input the saved learning values and codes into the new ECM using the GTS.


c.

Turn the ignition switch off and turn the GTS off.


d.

Wait for at least 30 seconds.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Clear DTC P062F stored in the ECM using the GTS.

HINT:
·

Each fuel injector has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the injector compensation codes to balance the different fuel injections between each fuel injector.

·

When you first turn the ignition switch to ON after replacing the ECM and other component(s), DTC P062F is stored. Manually clear the DTC upon completion of injector compensation code registration.



Replacement Part Utility Item
ECM
·

Learning Values Save

(Click here)

·

Learning Values Write

(Click here)


Fuel injector
·

Input Injector Compensation Code

(Click here)

·

Pilot Quantity Learning

(Click here)





CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P062F Ignition switch ON for 1 second

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION

·

After replacing an fuel injector, the ECM needs registration.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.LEARNING VALUES CONFIRMATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Engine and ECT / Utility / Learning values confirmation.

Powertrain > Engine and ECT > Utility
Tester Display
Learning Values Confirmation
50005 234 242

Result:
Result Proceed to
The injector compensation codes are not input A
The injector compensation codes registered in the ECM are different than the codes imprinted on the injectors A
The pilot quantity learning values are set to the default values B
Except above C


HINT:
·

When the catalyst deterioration learning values are set to the default values, "FFFFFFFF" is displayed.

·

When the pilot quantity learning values are set to the default values, "7FFF" is displayed.




A

2.REGISTER INJECTOR COMPENSATION CODE

B

7.LEARNING VALUES WRITE

C

4.CHECK DTC OUTPUT
2.REGISTER INJECTOR COMPENSATION CODE
a.

Result:
Proceed to
NEXT



NEXT

3.PILOT QUANTITY LEARNING
3.PILOT QUANTITY LEARNING
a.

Perform the fuel injector pilot quantity learning.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off and leave the vehicle for 30 seconds or more.


d.

Turn the ignition switch to ON for 1 second.


e.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

f.

Read the DTCs.


Result:
Result Proceed to
P062F is output A
No DTC is output B



A

5.REPLACE ECM

B

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off and leave the vehicle for 30 seconds or more.


d.

Turn the ignition switch to ON for 1 second.


e.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.LEARNING VALUES WRITE
HINT:

When replacing the ECM, after performing "Learning Values Save" to save the learned values from the old ECM using the GTS and replacing the old ECM with a new one, "Learning Values Write" was not performed using the GTS causing this DTC to be output.


a.

Install the old ECM.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Engine and ECT / Utility / Learning values save.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Learning Values Save
50005 234 240

e.

Remove the old ECM.


f.

Install a new ECM.


g.

Enter the following menus: Engine and ECT / Utility / Learning values write.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Learning Values Write
50005 234 241

Result:
Proceed to
NEXT



NEXT

8.LEARNING VALUES CONFIRMATION
8.LEARNING VALUES CONFIRMATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Engine and ECT / Utility / Learning values confirmation.

Powertrain > Engine and ECT > Utility
Tester Display
Learning Values Confirmation
50005 234 242

Result:
Result Proceed to
The pilot quantity learning values are set to the default values A
The catalyst deterioration learning values are set to the default values B
Except above C


HINT:
·

When the catalyst deterioration learning values are set to the default values, "FFFFFFFF" is displayed.

·

When the pilot quantity learning values are set to the default values, "7FFF" is displayed.




A

3.PILOT QUANTITY LEARNING

B

9.CATALYST RECORD CLEAR
9.CATALYST RECORD CLEAR

Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT