Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P2610  ECM / PCM Internal Engine Off Timer Performance  


DESCRIPTION

The soak timer operates after the ignition switch is turned off. When a certain amount of time has elapsed after turning the ignition switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.

A394575E01
0.927,0.646 1.385,0.844 0.458,0.198 10 false AM2 1.49,0.896 3.167,1.125 1.677,0.229 10 false Ignition Switch Assembly 1.76,0.396 2.219,0.594 0.458,0.198 10 false AM2 2.521,0.396 2.979,0.594 0.458,0.198 10 false IG2 3.698,0.667 4.021,0.865 0.323,0.198 10 false IGN 0.583,3.146 1.271,3.344 0.688,0.198 10 false FL MAIN 1.458,2.781 2.146,2.979 0.688,0.198 10 false EFI MAIN 3.073,3.604 3.76,3.802 0.688,0.198 10 false MAIN 4.344,3.375 5.031,3.573 0.688,0.198 10 false MREL 4.792,2.51 5.479,2.708 0.688,0.198 10 false +B2 4.813,2.052 5.5,2.25 0.688,0.198 10 false +B 4.813,0.385 5.5,0.583 0.688,0.198 10 false IGSW 5.406,2.24 6.531,2.448 1.125,0.208 10 false Power Source IC 5,0.76 5.979,0.979 0.979,0.219 10 false Soak Timer IC 5.031,3.24 6.521,3.448 1.49,0.208 10 false Main Relay Control IC 5.635,4.146 6.323,4.344 0.688,0.198 10 false ECM 0.74,3.99 1.427,4.188 0.688,0.198 10 false Battery

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2610 ECM / PCM Internal Engine Off Timer Performance ECM internal malfunction (2 trip detection logic). ECM Comes on DTC stored

MONITOR DESCRIPTION

·

While the engine is running, the ECM monitors the synchronization of the soak timer and the CPU clock. If these two are not synchronized, the ECM interprets this as a malfunction, illuminates the MIL and stores the DTC.

·

If the soak timer activates the ECM even though only a short amount of time has elapsed since the ignition switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the ignition switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores a DTC the next time the ignition switch is turned to ON.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).


HINT:
·

DTC P2610 is stored if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is necessary.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

2.CHECK WHETHER DTC OUTPUT RECURS
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON for 10 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

If no pending DTC is output, the repair has been successfully completed.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END