Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › from 2016.08
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System)  C142B  Motor Power Supply Voltage Circuit  C146C  Open in ABS Motor Relay Circuit  C146D  Short in ABS Motor Relay Circuit  


DESCRIPTION

The motor relay and motor fail-safe relay are built into the brake actuator assembly.

During ABS, TRC, VSC, or brake assist operation, the skid control ECU (brake actuator assembly) turns on the motor relay to run the pump motor in the brake actuator assembly.

When a motor system DTC is stored, the motor fail-safe relay cuts the power source supply to the motor relay for fail-safe operation.

These DTCs may be stored when the voltage to the motor relay power source (BM terminal) is lower than the DTC detection condition due to low output from the battery or alternator.

DTC No. Detection Item DTC Detection Condition Trouble Area
C142B Motor Power Supply Voltage Circuit When voltage at +BS terminal is 9.5 V or higher, open in BM terminal continues for 1 second or more.
·

ABS MTR fuse

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector


C146C Open in ABS Motor Relay Circuit When voltage at +BS terminal is 9.5 V or higher and motor relay ON while control operates, relay contact OFF condition continues for 0.12 seconds or more.
·

ABS MTR fuse

·

Brake actuator assembly (Motor relay)

·

Wire harness or connector


C146D Short in ABS Motor Relay Circuit Either of the following is detected:
1.

Overcurrent in motor relay and motor fail-safe relay continues for 0.05 seconds or more.

2.

Motor relay gate voltage malfunction continues for 0.12 seconds or more.


·

Brake actuator assembly (Motor relay)

·

Wire harness or connector



WIRING DIAGRAM

C283801E24
0.271,1.333 1.104,1.521 0.833,0.188 10 false from Battery 1.802,1.521 2.667,1.729 0.865,0.208 10 false ABS MTR 3.406,1.229 3.719,1.427 0.313,0.198 10 false 13 3.667,1.24 4.042,1.438 0.375,0.198 10 false BM 4.667,0.573 5.813,0.771 1.146,0.198 10 false Skid Control ECU 4.938,3.354 5.729,3.552 0.792,0.198 10 false Motor Relay 4.667,1.323 6.115,1.542 1.448,0.219 10 false Motor Fail Safe Relay 5.229,4.427 6.063,4.625 0.833,0.198 10 false Pump Motor 4.188,4.875 4.646,5.073 0.458,0.198 10 false A42 4.198,5.063 5.833,5.271 1.635,0.208 10 false Brake Actuator Assembly 3.417,2.844 3.729,3.042 0.313,0.198 10 false 1 3.677,2.854 4.292,3.052 0.615,0.198 10 false GND2

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When C1241 and/or C1417 is output together with C142B, C146C and/or C146D inspect and repair the trouble areas indicated by C1241 and/or C1417 first.

for C1241: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>C1241

for C1417: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>C1417


PROCEDURE

1.CHECK TERMINAL VOLTAGE (BM TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.
C363591C03
1.521,0.125 1.917,0.354 0.396,0.229 2.719,0.927 3.167,1.479 3.167,1.479 3.167,1.698 true 1.594,0.146 1.906,0.344 0.313,0.198 10 false A42 3.063,1.74 3.333,1.938 0.271,0.198 10 false BM
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the A42 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-13 (BM) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BM CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.
C364797C05
1.542,0.104 1.917,0.333 0.375,0.229 0.25,1.365 0.25,1.198 0.25,1.198 0.781,0.885 true 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 1.604,0.125 1.917,0.323 0.313,0.198 10 false A42 0.052,1.427 0.583,1.635 0.531,0.208 10 false GND2
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-1 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)

3.RECONFIRM DTC
HINT:

These codes are stored when a problem is identified in the skid control ECU (brake actuator assembly). The motor relay is in the skid control ECU (brake actuator assembly). Therefore, motor relay inspections and motor relay unit inspections cannot be performed. Be sure to check if any DTCs are output before replacing the brake actuator assembly.


a.

Reconnect the A42 skid control ECU (brake actuator assembly) connector.



Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTCs C142B, C146C and C146D are not output
DTCs C142B, C146C and/or C146D are output


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch turned to ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.




DTCs C142B, C146C and C146D are not output

DTCs C142B, C146C and/or C146D are output