Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › from 2016.08
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System)  C1407  Open or Short in Rear Speed Sensor RH Circuit  C1408  Open or Short in Rear Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1403 and C1404.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>C1403

DTC No. Detection Item DTC Detection Condition Trouble Area
C1407 Open or Short in Rear Speed Sensor RH Circuit Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor RH

·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)

·

Skid control sensor wire


C1408 Open or Short in Rear Speed Sensor LH Circuit Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor LH

·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)

·

Skid control sensor wire



WIRING DIAGRAM

C217557E35
5.542,2.75 5.958,2.896 0.417,0.146 10 false A42 5.531,2.896 7.083,3.302 1.552,0.406 10 false Skid Control ECU (Brake Actuator Assembly) 3.125,2.75 5.198,2.927 2.073,0.177 10 false Skid Control Sensor Wire 3.979,0.333 4.26,0.5 0.281,0.167 10 false V3 3.969,0.875 4.25,1.042 0.281,0.167 10 false V3 3.969,1.875 4.25,2.042 0.281,0.167 10 false V3 3.969,2.448 4.25,2.615 0.281,0.167 10 false V3 2.844,0.323 2.99,0.469 0.146,0.146 10 false C 2.844,0.875 2.99,1.021 0.146,0.146 10 false C 2.844,1.875 2.99,2.021 0.146,0.146 10 false D 2.844,2.448 2.99,2.594 0.146,0.146 10 false D 0.458,0.542 2,0.75 1.542,0.208 10 false Rear Speed Sensor RH 0.479,2.115 2.021,2.323 1.542,0.208 10 false Rear Speed Sensor LH 2.406,0.875 2.698,1.052 0.292,0.177 10 false RR- 2.865,0.125 2.969,0.271 0.104,0.146 10 false 3 2.396,0.323 2.708,0.5 0.313,0.177 10 false RR+ 4,0.688 4.135,0.854 0.135,0.167 10 false 4 4,0.135 4.177,0.292 0.177,0.156 10 false 3 2.854,0.667 3.031,0.823 0.177,0.156 10 false 1 2.385,2.448 2.677,2.625 0.292,0.177 10 false RL- 2.854,1.677 2.969,1.833 0.115,0.156 10 false 3 2.396,1.885 2.688,2.063 0.292,0.177 10 false RL+ 4.01,2.24 4.146,2.406 0.135,0.167 10 false 2 4.01,1.677 4.188,1.833 0.177,0.156 10 false 1 2.844,2.25 2.948,2.406 0.104,0.156 10 false 1 6.167,0.865 6.458,1.042 0.292,0.177 10 false RR- 6.167,0.333 6.542,0.51 0.375,0.177 10 false RR+ 6.167,2.438 6.458,2.615 0.292,0.177 10 false RL- 6.167,1.885 6.458,2.063 0.292,0.177 10 false RL+ 5.823,0.74 6.021,0.906 0.198,0.167 10 false 15 5.823,0.208 6.021,0.375 0.198,0.167 10 false 16 5.823,2.323 6.021,2.542 0.198,0.219 10 false 28 5.833,1.76 6.021,1.969 0.188,0.208 10 false 29 3.573,0.438 3.885,0.615 0.313,0.177 10 false RR+ 3.583,0.771 3.875,0.948 0.292,0.177 10 false RR- 3.594,1.99 3.885,2.167 0.292,0.177 10 false RL+ 3.604,2.333 3.896,2.51 0.292,0.177 10 false RL-

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CHECK FOR INTERMITTENT PROBLEMS


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection Normal or Error Normal Error: Momentary interruption
RL Speed Open Rear speed sensor LH open detection Normal or Error Normal Error: Momentary interruption
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Open
RL Speed Open
50003 105 202,203
OK:

Normal (There are no momentary interruptions).


HINT:

Perform the above inspection before removing the sensor and connector.


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (REAR SPEED SENSOR)

NG

4.INSPECT SKID CONTROL SENSOR WIRE
2.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed:
No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed:
No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4
g.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.INSPECT SKID CONTROL SENSOR WIRE
3.RECONFIRM DTC

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTCs C1407 and C1408 are not output
DTCs C1407 and/or C1408 are output



DTCs C1407 and C1408 are not output

DTCs C1407 and/or C1408 are output

4.INSPECT SKID CONTROL SENSOR WIRE
C269768C04
1.198,0.813 1.365,1 0.167,0.188 3.427,0.542 3.729,0.74 0.302,0.198 5.844,0.833 6.021,1.01 0.177,0.177 0.635,2.115 0.635,2.021 0.635,2.021 1.042,1.563 false 1.927,2.125 1.927,2.021 1.927,2.021 1.51,1.573 false 5.385,2.146 5.385,2.021 5.385,2.021 5.698,1.563 false 6.479,2.135 6.479,2.031 6.479,2.031 6.177,1.563 false 3.792,1.344 4.167,0.833 4.167,0.833 4.25,0.833 true 3.458,1.344 3.167,0.833 3.167,0.833 3.083,0.833 true 3.427,1.573 2.917,1.917 2.917,1.917 2.917,2.083 true 3.792,1.583 4.25,1.917 4.25,1.917 4.25,2.083 true 6.094,0.708 6.406,0.865 0.313,0.156 10 false *A 1.417,0.688 1.729,0.844 0.313,0.156 10 false *B 0.083,0.094 0.396,0.25 0.313,0.156 10 false *1 1.208,2.229 1.521,2.385 0.313,0.156 10 false *a 3.563,2.146 3.875,2.302 0.313,0.156 10 false *b 3.76,0.406 4.073,0.563 0.313,0.156 10 false *c 1.24,0.833 1.396,1.031 0.156,0.198 10 false D 3.5,0.563 3.823,0.75 0.323,0.188 10 false V3 5.885,0.844 6.042,1.042 0.156,0.198 10 false C 0.552,2.146 0.865,2.333 0.313,0.188 10 false RL- 1.813,2.156 2.115,2.323 0.302,0.167 10 false RL+ 5.302,2.167 5.604,2.354 0.302,0.188 10 false RR- 6.375,2.167 6.677,2.344 0.302,0.177 10 false RR+ 5.896,2.292 6.104,2.479 0.208,0.188 10 false *a 4.281,0.76 4.594,0.948 0.313,0.188 10 false RL- 2.781,0.75 3.083,0.917 0.302,0.167 10 false RL+ 2.823,2.094 3.125,2.271 0.302,0.177 10 false RR+ 4.167,2.125 4.469,2.313 0.302,0.188 10 false RR-
*A for RH *B for LH
*1 Skid Control Sensor Wire - -
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)
*c Female - -


a.

Turn the ignition switch off.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
V3 female connector 3 (RR+) - C-3 (RR+) Always Below 1 Ω
V3 female connector 3 (RR+) or C-3 (RR+) - Body ground Always 10 kΩ or higher
V3 female connector 4 (RR-) - C-1 (RR-) Always Below 1 Ω
V3 female connector 4 (RR-) or C-1 (RR-) - Body ground Always 10 kΩ or higher
V3 female connector 3 (RR+) - V3 female connector 1 (RL+) Always 10 kΩ or higher
V3 female connector 3 (RR+) - V3 female connector 2 (RL-) Always 10 kΩ or higher
V3 female connector 3 (RR+) - V3 female connector 4 (RR-) Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
V3 female connector 1 (RL+) - D-3 (RL+) Always Below 1 Ω
V3 female connector 1 (RL+) or D-3 (RL+) - Body ground Always 10 kΩ or higher
V3 female connector 2 (RL-) - D-1 (RL-) Always Below 1 Ω
V3 female connector 2 (RL-) or D-1 (RL-) - Body ground Always 10 kΩ or higher
V3 female connector 1 (RL+) - V3 female connector 2 (RL-) Always 10 kΩ or higher
V3 female connector 1 (RL+) - V3 female connector 3 (RR+) Always 10 kΩ or higher
V3 female connector 1 (RL+) - V3 female connector 4 (RR-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
a.

Turn the ignition switch off.



c.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the C and/or D speed sensor connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A42-16 (RR+) - C-3 (RR+) Always Below 1 Ω
A42-16 (RR+) or C-3 (RR+) - Body ground Always 10 kΩ or higher
A42-15 (RR-) - C-1 (RR-) Always Below 1 Ω
A42-15 (RR-) or C-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A42-29 (RL+) - D-3 (RL+) Always Below 1 Ω
A42-29 (RL+) or D-3 (RL+) - Body ground Always 10 kΩ or higher
A42-28 (RL-) - D-1 (RL-) Always Below 1 Ω
A42-28 (RL-) or D-1 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (RR+/RL+ TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RR+/RL+ TERMINAL)
a.

Reconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.
C269769C05
1.604,0.135 1.833,0.333 0.229,0.198 1.604,0.406 1.833,0.594 0.229,0.188 2,1.281 2.698,1.469 2.698,1.469 2.698,1.563 false 1.885,0.083 2.198,0.24 0.313,0.156 10 false *A 1.885,0.375 2.198,0.531 0.313,0.156 10 false *B 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 1.667,0.146 1.823,0.344 0.156,0.198 10 false C 1.667,0.417 1.823,0.615 0.156,0.198 10 false D 2.49,1.583 2.948,1.781 0.458,0.198 10 false RR+ 2.49,1.75 2.948,1.948 0.458,0.198 10 false RL+ 2.76,1.583 3.073,1.781 0.313,0.198 10 false *A, 2.75,1.75 3.063,1.948 0.313,0.198 10 false *B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
C-3 (RR+) - Body ground Ignition switch ON 11 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
D-3 (RL+) - Body ground Ignition switch ON 11 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

NG