Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › from 2016.08
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System)  C1268  Transfer L4 Position Switch Circuit  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1268 Transfer L4 Position Switch Circuit Either of the following is detected:
·

No signal is input to the EXI4 terminal of the skid control ECU.

·

A data malfunction signal is received from the L4 position switch (No. 1 transfer indicator switch).


·

L4 position switch (No. 1 transfer indicator switch)

·

L4 position switch (No. 1 transfer indicator switch) circuit

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C363590E02
0.156,3.177 3.063,3.448 2.906,0.271 10 false Skid Control ECU (Brake Actuator Assembly) 0.167,2.99 0.563,3.177 0.396,0.188 10 false A42 2.01,2.583 2.417,2.792 0.406,0.208 10 false EXI4 2.49,1.823 2.865,2.031 0.375,0.208 10 false 27 4.417,3.156 4.74,3.365 0.323,0.208 10 false C36 4.427,3.323 6.542,3.698 2.115,0.375 10 false L4 Position Switch (No. 1 Transfer Indicator Switch) 6.26,2.458 6.635,2.667 0.375,0.208 10 false 1 4.365,2.458 4.688,2.667 0.323,0.208 10 false 2 1.896,1.958 2.344,2.177 0.448,0.219 10 false HDCS 2.49,2.458 2.865,2.667 0.375,0.208 10 false 5 2.469,0.302 2.844,0.51 0.375,0.208 10 false 19 2.135,0.438 2.427,0.646 0.292,0.208 10 false L4 1.292,0.865 1.625,1.052 0.333,0.188 10 false A29 1.271,1.052 1.667,1.26 0.396,0.208 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (EXI4/HDSC TERMINAL)
a.

Shift the transfer to L4, and then drive the vehicle.


b.

Turn the ignition switch off.


c.

Disconnect the A29 ECM connector.


d.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-5 (EXI4) - Body ground Transfer shifted to L4 Below 1 Ω
A42-27 (HDSC) - Body ground Transfer shifted to L4 Below 1 Ω



f.

Reconnect the A42 skid control ECU (brake actuator assembly) connector.


g.

Turn the ignition switch to ON.


h.

Shift the transfer to H2 or H4, and then drive the vehicle.


i.

Turn the ignition switch off.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-5 (EXI4) - Body ground Transfer shifted to H2 or H4 10 kΩ or higher
A42-27 (HDSC) - Body ground Transfer shifted to H2 or H4 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.RECONFIRM DTC

NG

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - NO. 1 TRANSFER INDICATOR SWITCH)
2.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Reconnect the A29 ECM connector.


c.

Reconnect the A42 skid control ECU (brake actuator assembly) connector.


d.

Turn the ignition switch to ON.



f.

Turn the ignition switch off.


g.

Start the engine.


h.

Shift the transfer to H2 or H4.


i.

Shift the transfer to L4, drive the vehicle, and then check for DTCs.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is output
DTC is not output




DTC is output

DTC is not output

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - NO. 1 TRANSFER INDICATOR SWITCH)
a.

Turn the ignition switch off.


b.

Disconnect the C36 L4 position switch (No. 1 transfer indicator switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-5 (EXI4) - C36-2 Always Below 1 Ω
A42-27 (HDCS) - C36-2 Always Below 1 Ω
A42-5 (EXI4) - Body ground Always 10 kΩ or higher
A42-27 (HDCS) - Body ground Always 10 kΩ or higher
C36-2 - Body ground Always 10 kΩ or higher
C36-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 1 TRANSFER INDICATOR SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT NO. 1 TRANSFER INDICATOR SWITCH
a.

Remove the L4 position switch (No. 1 transfer indicator switch).

Click hereDrivetrain>HF1A (TRANSFER / 4WD / AWD)>TRANSFER INDICATOR SWITCH>REMOVAL


b.

Inspect the L4 position switch (No. 1 transfer indicator switch).

Click hereDrivetrain>HF1A (TRANSFER / 4WD / AWD)>TRANSFER INDICATOR SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 1 TRANSFER INDICATOR SWITCH