Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › 2016.08–2017.01
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display the DTC by blinking the ABS warning light and slip indicator light.

WIRING DIAGRAM

C363589E01
0.51,4.313 2.229,4.5 1.719,0.188 10 false : CAN Communication Line 0.792,3.542 1.188,3.719 0.396,0.177 10 false ECM 3.417,3.344 3.813,3.521 0.396,0.177 10 false I17 3.417,3.542 3.813,3.719 0.396,0.177 10 false DLC3 5.552,2.063 7.083,2.458 1.531,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 5.552,1.896 5.979,2.115 0.427,0.219 10 false A42 5.958,1.396 6.448,1.583 0.49,0.188 10 false CANL 5.958,0.698 6.448,0.885 0.49,0.188 10 false CANH 5.656,1.208 6.052,1.385 0.396,0.177 10 false 10 5.656,0.51 6.052,0.688 0.396,0.177 10 false 22 0.802,3.323 1.198,3.5 0.396,0.177 10 false A29 1.396,2.031 1.792,2.208 0.396,0.177 10 false 27 1.396,1.208 1.792,1.385 0.396,0.177 10 false 49 1.396,0.51 1.792,0.688 0.396,0.177 10 false 41 0.885,0.708 1.354,0.906 0.469,0.198 10 false CANH 0.875,1.406 1.365,1.594 0.49,0.188 10 false CANL 1.073,2.156 1.563,2.344 0.49,0.188 10 false TC 3.427,2.167 3.917,2.354 0.49,0.188 10 false TC 3.406,2.792 3.896,2.979 0.49,0.188 10 false CG 3.177,2.635 3.667,2.823 0.49,0.188 10 false 4 3.094,2.021 3.583,2.208 0.49,0.188 10 false 13

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ VSC)>DIAGNOSIS SYSTEM


Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.INSPECT DLC3

DTC is output

2.INSPECT DLC3
a.
C269109C81
0.115,1.49 0.479,1.719 0.365,0.229 1.635,1.813 1.823,1.49 true 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 1.521,1.844 1.833,2.042 0.313,0.198 10 false TC 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.219,1.521 0.531,1.719 0.313,0.198 10 false I17
*a Front view of DLC3


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I17-13 (TC) - I17-4 (CG) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

3.REPLACE ECM

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
3.REPLACE ECM
a.
C269109C81
0.115,1.49 0.479,1.719 0.365,0.229 1.635,1.813 1.823,1.49 true 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 1.521,1.844 1.833,2.042 0.313,0.198 10 false TC 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.219,1.521 0.531,1.719 0.313,0.198 10 false I17
*a Front view of DLC3


Turn the ignition switch off.



c.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


SST
09843-18040  

d.

Check that the ABS warning and slip indicator light are blinking.

OK:

The ABS warning and slip indicator light are blinking.



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the A29 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-13 (TC) - A29-27 (TC) Always Below 1 Ω
I17-13 (TC) or A29-27 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C269109C82
0.115,1.49 0.479,1.719 0.365,0.229 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.208,1.521 0.521,1.719 0.313,0.198 10 false I17
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE ECM
a.
C269109C81
0.115,1.49 0.479,1.719 0.365,0.229 1.635,1.813 1.823,1.49 true 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 1.521,1.844 1.833,2.042 0.313,0.198 10 false TC 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.219,1.521 0.531,1.719 0.313,0.198 10 false I17
*a Front view of DLC3


Replace the ECM.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL


b.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


SST
09843-18040  

c.

Check that the ABS warning and slip indicator light are blinking.

OK:

The ABS warning and slip indicator light are blinking.



Result:
Proceed to
OK
NG



OK

END

NG