Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › from 2016.08
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System)  C1422  Master Cylinder Pressure Sensor Zero Point High Malfunction  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction When vehicle speed is 3 km/h (2 mph) or more and stop light switch assembly is off, master cylinder pressure continuously exceeds 1.764 MPa (18.0 kgf/cm2, 255 psi) for 5 seconds or more.
·

Stop light switch assembly

·

Harness or connector

·

Skid control ECU (Brake actuator assembly)

·

Brake actuator assembly (Master cylinder pressure sensor)



WIRING DIAGRAM

C325963E15
4.854,2.219 5.313,2.417 0.458,0.198 10 false GND1 4.563,0.823 5.021,1.021 0.458,0.198 10 false 35 4.573,2.083 5.073,2.281 0.5,0.198 10 false 25 4.833,2.927 5.292,3.125 0.458,0.198 10 false A42 4.833,3.135 6.385,3.531 1.552,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 0.125,0.958 2.448,1.323 2.323,0.365 10 false from Stop Light Switch Assembly 0.927,1.635 2.604,2.01 1.677,0.375 10 false to Stop Light Circuit 4.865,0.958 5.25,1.177 0.385,0.219 10 false STP

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CALIBRATION


PROCEDURE

1.CHECK DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.


e.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC C1422 is output
DTCs C1422 and C1425 are output




DTC C1422 is output

2.READ VALUE USING GTS (STOP LIGHT SWITCH)

DTCs C1422 and C1425 are output

2.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

In accordance with the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF OFF: Brake pedal released
ON: Brake pedal depressed
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37
f.

Check that the stop light switch assembly condition observed on the GTS changes according to brake pedal operation.


OK:

The GTS displays ON or OFF according to brake pedal operation.


Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)

NG

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
3.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

In accordance with the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Master Cylinder Pressure Master cylinder pressure sensor pressure Min.: 0.00 MPa
Max.: 23.28 MPa
Brake pedal operated: Proportional to pedal force
Brake pedal released: 0.00 to 1.76 MPa
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Master Cylinder Pressure
50003 105 393
OK:

Data List pressure is within standard range.


Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

4.RECONFIRM DTC

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC C1422 is not output
DTC C1422 is output



DTC C1422 is not output

DTC C1422 is output

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch assembly installation.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL>ADJUSTMENT

OK:

The brake pedal height and stop light switch assembly installation are normal.



Result:
Proceed to
OK
NG



OK

6.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

6.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION

OK:

The stop light switch assembly is normal.


Result:
Proceed to
OK
NG




OK

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C364797C04
1.542,0.104 1.917,0.333 0.375,0.229 2.677,1.885 2.677,1.74 2.677,1.74 2.271,1.281 true 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 1.604,0.125 1.917,0.323 0.313,0.198 10 false A42 2.542,1.948 2.969,2.177 0.427,0.229 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-35 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)