Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.08–2022.09
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0138307 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1620/21  Side Airbag Sensor RH Circuit Malfunction  


DESCRIPTION

The door side airbag sensor RH consists of a diagnostic circuit and side deceleration sensor, etc.

If the airbag sensor assembly receives signals from the side deceleration sensor, it determines whether the SRS should be activated.

DTC B1620/21 is stored when a malfunction is detected in the door side airbag sensor RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1620/21 Side Airbag Sensor RH Circuit Malfunction Either condition is met:
·

A door side airbag sensor RH malfunction.

·

An airbag sensor assembly malfunction.


·

Door side airbag sensor RH

·

Airbag sensor assembly



WIRING DIAGRAM

C305104E14
1.167,0.917 1.625,1.115 0.458,0.198 10 false BBR+ 1.198,2.083 1.656,2.281 0.458,0.198 10 false BBR- 1.688,0.781 2.146,0.979 0.458,0.198 10 false 2 1.677,1.938 2.135,2.135 0.458,0.198 10 false 1 5.333,0.781 5.792,0.979 0.458,0.198 10 false 8 5.323,1.979 5.781,2.177 0.458,0.198 10 false 11 0.354,2.813 1.938,3.031 1.583,0.219 10 false S23 5.281,2.792 6.74,3.01 1.458,0.219 10 false S21 0.344,2.969 2.417,3.229 2.073,0.26 10 false Door Side Airbag Sensor RH 5.281,2.969 7.031,3.344 1.75,0.375 10 false Airbag Sensor Assembly 5.635,0.906 6.094,1.104 0.458,0.198 10 false BBR+ 5.625,2.104 6.083,2.302 0.458,0.198 10 false BBR-

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK DOOR SIDE AIRBAG SENSOR RH
a.
C171812C40
0.896,1.271 1.208,1.427 0.313,0.156 10 *1 2.125,1.125 2.438,1.281 0.313,0.156 10 *2
*1 Door Side Airbag Sensor LH
*2 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Interchange the door side airbag sensor RH with LH and connect the connectors to them.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 63

g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 63
Result:
Proceed to
DTC B1620/21 is output
DTC B1625/22 is output
DTC B1620/21 and B1625/22 are not output


HINT:

Codes other than DTC B1620/21 and B1625/22 may be output at this time, but they are not related to this check.



j.

Turn the ignition switch off.


k.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


l.

Return the door side airbag sensor LH and RH to their original positions and connect the connectors to them.



DTC B1620/21 is output

DTC B1625/22 is output

DTC B1620/21 and B1625/22 are not output