Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.08–2021.07
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0138307 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1800/51  Short in Driver Side Squib Circuit  B1801/51  Open in Driver Side Squib Circuit  B1802/51  Short to GND in Driver Side Squib Circuit  B1803/51  Short to B+ in Driver Side Squib Circuit  


DESCRIPTION

The driver side squib circuit consists of the airbag sensor assembly, spiral cable sub-assembly and horn button assembly.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1800/51 Short in Driver Side Squib Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal 5 times in the driver side squib circuit during the primary check.

·

A horn button assembly malfunction.

·

A spiral cable sub-assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Cowl wire

·

Instrument panel wire

·

Spiral cable sub-assembly

·

Horn button assembly

·

Airbag sensor assembly


B1801/51 Open in Driver Side Squib Circuit One of the following conditions is met:
·

The airbag sensor assembly detects an open circuit signal in the driver side squib circuit for 2 seconds.

·

A horn button assembly malfunction.

·

A spiral cable sub-assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Cowl wire

·

Instrument panel wire

·

Spiral cable sub-assembly

·

Horn button assembly

·

Airbag sensor assembly


B1802/51 Short to GND in Driver Side Squib Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to ground signal in the driver side squib circuit for 0.5 seconds.

·

A horn button assembly malfunction.

·

A spiral cable sub-assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Cowl wire

·

Instrument panel wire

·

Spiral cable sub-assembly

·

Horn button assembly

·

Airbag sensor assembly


B1803/51 Short to B+ in Driver Side Squib Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to B+ signal in the driver side squib circuit for 0.5 seconds.

·

A horn button assembly malfunction.

·

A spiral cable sub-assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Cowl wire

·

Instrument panel wire

·

Spiral cable sub-assembly

·

Horn button assembly

·

Airbag sensor assembly



WIRING DIAGRAM

C303687E05
2.177,1.573 2.49,1.771 0.313,0.198 10 false D+ 2.146,2.396 2.458,2.594 0.313,0.198 10 false D- 2.458,2.406 2.771,2.604 0.313,0.198 10 false 1 2.458,1.594 2.771,1.792 0.313,0.198 10 false 2 2.927,1.563 3.24,1.76 0.313,0.198 10 false D+ 3,2.417 3.313,2.615 0.313,0.198 10 false D- 3.229,1.594 3.542,1.792 0.313,0.198 10 false 1 3.24,2.406 3.552,2.604 0.313,0.198 10 false 2 0.771,3.021 1.083,3.219 0.313,0.198 10 false z2 0.771,3.188 2.208,3.552 1.438,0.365 10 false Horn Button Assembly 2.51,3.042 2.823,3.24 0.313,0.198 10 false L29 2.521,3.219 4.25,3.458 1.729,0.24 10 false Spiral Cable Sub-assembly 3.917,1.469 4.229,1.667 0.313,0.198 10 false 1 3.927,2.302 4.24,2.5 0.313,0.198 10 false 2 3.885,1.885 4.198,2.083 0.313,0.198 10 false D+ 3.906,2.729 4.219,2.927 0.313,0.198 10 false D- 4.552,1.563 4.865,1.76 0.313,0.198 10 false 5 4.573,2.385 4.885,2.583 0.313,0.198 10 false 6 4.76,1.698 5.073,1.896 0.313,0.198 10 false D+ 4.771,2.531 5.083,2.729 0.313,0.198 10 false D- 4.729,4.146 5.042,4.344 0.313,0.198 10 false I51 4.74,4.313 6.854,4.583 2.115,0.271 10 false Airbag Sensor Assembly 3.875,1.677 7.156,2.031 3.281,0.354 10 false IL4 0.146,0.125 1.396,0.854 1.25,0.729 12 false : for LHD 3.875,2.521 7.156,2.875 3.281,0.354 10 false IL4

C303687E06
2.177,1.573 2.49,1.771 0.313,0.198 10 false D+ 2.146,2.396 2.458,2.594 0.313,0.198 10 false D- 2.458,2.406 2.771,2.604 0.313,0.198 10 false 1 2.458,1.594 2.771,1.792 0.313,0.198 10 false 2 2.927,1.563 3.24,1.76 0.313,0.198 10 false D+ 3,2.417 3.313,2.615 0.313,0.198 10 false D- 3.229,1.594 3.542,1.792 0.313,0.198 10 false 1 3.24,2.406 3.552,2.604 0.313,0.198 10 false 2 0.771,3.021 1.083,3.219 0.313,0.198 10 false z2 0.771,3.188 2.208,3.552 1.438,0.365 10 false Horn Button Assembly 2.51,3.042 2.823,3.24 0.313,0.198 10 false L29 2.521,3.219 4.25,3.458 1.729,0.24 10 false Spiral Cable Sub-assembly 3.906,1.479 4.219,1.677 0.313,0.198 10 false 1 3.917,2.323 4.229,2.521 0.313,0.198 10 false 2 3.885,1.885 4.198,2.083 0.313,0.198 10 false D+ 3.906,2.729 4.219,2.927 0.313,0.198 10 false D- 4.552,1.563 4.865,1.76 0.313,0.198 10 false 5 4.573,2.385 4.885,2.583 0.313,0.198 10 false 6 4.76,1.698 5.073,1.896 0.313,0.198 10 false D+ 4.771,2.531 5.083,2.729 0.313,0.198 10 false D- 4.729,4.146 5.042,4.344 0.313,0.198 10 false I51 4.74,4.313 6.854,4.583 2.115,0.271 10 false Airbag Sensor Assembly 3.885,1.677 7.156,2.052 3.271,0.375 10 false IL7 0.135,0.104 2.167,0.552 2.031,0.448 12 false : for RHD 3.885,2.521 7.156,2.896 3.271,0.375 10 false IL7

CAUTION / NOTICE / HINT

NOTICE:
·

When installing the spiral cable sub-assembly and steering wheel, be sure to adjust the spiral cable sub-assembly as it may break if the steering wheel is turned before adjusting the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.*

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

*: w/ VSC



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK HORN BUTTON ASSEMBLY
a.

Turn the ignition switch off.

C212502C01
4.094,1.448 4.458,1.667 0.365,0.219 0.344,1.104 0.344,1.458 false 5.635,1.563 6.021,1.865 false 5.417,1.927 5.802,2.229 false 0.281,1.51 0.594,1.667 0.313,0.156 10 false *1 1.083,1.427 1.396,1.583 0.313,0.156 10 false *2 2.729,1.729 3.042,1.885 0.313,0.156 10 false *3 5.688,0.896 6,1.052 0.313,0.156 10 false *4 6.063,1.802 6.375,1.958 0.313,0.156 10 false *5 5.177,0.573 5.49,0.729 0.313,0.156 10 false *a 5.885,2.229 6.198,2.385 0.313,0.156 10 false *b 0.417,1.188 0.729,1.344 0.313,0.156 10 false H 0.625,1.188 0.938,1.344 0.313,0.156 10 false G 1.625,1.198 1.938,1.354 0.313,0.156 10 false F 1.74,1.198 2.052,1.354 0.313,0.156 10 false E 1.979,1.208 2.292,1.365 0.313,0.156 10 false D 2.094,1.208 2.406,1.365 0.313,0.156 10 false C 2.542,0.958 2.854,1.115 0.313,0.156 10 false A 4.156,1.479 4.469,1.635 0.313,0.156 10 false z2
*1 Driver Side Squib *2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly *4 Connector G
*5 SST - -
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Orange



b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the horn button assembly.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector G (orange connector).

CAUTION:

Never connect the tester to the horn button assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output
DTC B1800/51, B1801/51, B1802/51 or B1803/51 is output


HINT:

Codes other than DTC B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


m.

Disconnect SST from connector G.



DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is output

2.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Disconnect the connector from the airbag sensor assembly.


b.
C305107C01
0.115,0.677 0.427,0.833 0.313,0.156 10 false *1 1.042,1.448 1.354,1.604 0.313,0.156 10 false *2 2.854,1.792 3.167,1.948 0.313,0.156 10 false *3 0.271,1.156 0.583,1.313 0.313,0.156 10 false H 0.469,1.156 0.781,1.313 0.313,0.156 10 false G 1.49,1.156 1.802,1.313 0.313,0.156 10 false F 1.615,1.156 1.927,1.313 0.313,0.156 10 false E 1.906,1.167 2.219,1.323 0.313,0.156 10 false D 2.031,1.167 2.344,1.323 0.313,0.156 10 false C 2.615,0.896 2.927,1.052 0.313,0.156 10 false A 2.292,1.167 2.604,1.323 0.313,0.156 10 false B
*1 Driver Side Squib
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly


Check that the connectors (on the airbag sensor assembly side and horn button assembly side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK DRIVER SIDE SQUIB CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK DRIVER SIDE SQUIB CIRCUIT
a.
C303689C03
0.635,2.115 0.979,2.323 0.344,0.208 1.833,2.625 2.031,2.76 false 1.719,2.115 2.021,2.313 true 1.646,2.115 1.344,2.313 true 0.135,0.458 0.448,0.615 0.313,0.156 10 false *1 1.031,1.198 1.344,1.354 0.313,0.156 10 false *2 2.76,1.594 3.073,1.75 0.313,0.156 10 false *3 2.01,1.979 2.323,2.135 0.313,0.156 10 false *4 1.594,1.573 1.906,1.729 0.313,0.156 10 false *a 2.063,2.74 2.375,2.896 0.313,0.156 10 false *b 1.177,2.24 1.49,2.396 0.313,0.156 10 false D- 2.063,2.271 2.375,2.427 0.313,0.156 10 false D+ 0.698,2.146 1.01,2.302 0.313,0.156 10 false z2 0.302,0.958 0.615,1.115 0.313,0.156 10 false H 0.521,0.958 0.833,1.115 0.313,0.156 10 false G 1.531,0.969 1.844,1.125 0.313,0.156 10 false F 1.677,0.969 1.99,1.125 0.313,0.156 10 false E 1.927,0.969 2.24,1.125 0.313,0.156 10 false D 2.063,0.969 2.375,1.125 0.313,0.156 10 false C 2.313,0.958 2.625,1.115 0.313,0.156 10 false B 2.667,0.667 2.979,0.823 0.313,0.156 10 false A
*1 Driver Side Squib
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Connector G
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Orange


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z2-2 (D+) - Body ground Ignition switch ON Below 1 V
z2-1 (D-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-2 (D+) - z2-1 (D-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-2 (D+) - z2-1 (D-) Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-2 (D+) - Body ground Always 1 MΩ or higher
z2-1 (D-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

5.CHECK DRIVER SIDE SQUIB CIRCUIT
4.CHECK DTC
a.
C212504C01
0.135,0.281 0.448,0.438 0.313,0.156 10 false *1 0.917,0.99 1.229,1.146 0.313,0.156 10 false *2 2.667,1.333 2.979,1.49 0.313,0.156 10 false *3 0.313,0.708 0.625,0.865 0.313,0.156 10 false H 0.458,0.708 0.771,0.865 0.313,0.156 10 false G 1.542,0.719 1.854,0.875 0.313,0.156 10 false F 1.677,0.719 1.99,0.875 0.313,0.156 10 false E 1.917,0.708 2.229,0.865 0.313,0.156 10 false D 2.063,0.708 2.375,0.865 0.313,0.156 10 false C 2.458,0.469 2.771,0.625 0.313,0.156 10 false A
*1 Driver Side Squib
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly


Connect the connectors to the horn button assembly and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 63

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 63
Result:
Proceed to
DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output
DTC B1800/51, B1801/51, B1802/51 or B1803/51 is output


HINT:

Codes other than DTC B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.




DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is output

5.CHECK DRIVER SIDE SQUIB CIRCUIT
a.

Disconnect the instrument panel wire connector from the spiral cable sub-assembly.

C303692C01
4.854,0.771 5.219,1.01 0.365,0.24 5.458,1.292 5.896,0.896 true 6.469,1.333 6.042,0.896 true 0.646,0.448 0.958,0.604 0.313,0.156 10 false *1 1.542,1.052 1.854,1.208 0.313,0.156 10 false *2 3.479,1.375 3.792,1.531 0.313,0.156 10 false *3 6.354,0.375 6.667,0.531 0.313,0.156 10 false *6 5.802,0.167 6.115,0.323 0.313,0.156 10 false *a 0.938,0.833 1.25,0.99 0.313,0.156 10 false H 1.156,0.833 1.469,0.99 0.313,0.156 10 false G 2.073,0.833 2.385,0.99 0.313,0.156 10 false F 2.292,0.833 2.604,0.99 0.313,0.156 10 false E 2.51,0.833 2.823,0.99 0.313,0.156 10 false D 2.656,0.833 2.969,0.99 0.313,0.156 10 false C 2.875,0.833 3.188,0.99 0.313,0.156 10 false B 3.302,0.573 3.615,0.729 0.313,0.156 10 false A 5.375,1.323 5.688,1.479 0.313,0.156 10 false D- 6.417,1.354 6.729,1.51 0.313,0.156 10 false D+ 4.917,0.813 5.229,0.969 0.313,0.156 10 false L29 2.375,0.385 2.688,0.542 0.313,0.156 10 false *4 2.708,0.375 3.021,0.531 0.313,0.156 10 false *5
*1 Horn Button Assembly *2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly *4 Instrument Panel Wire
*5 Cowl Wire *6 Connector E
*a Rear view of wire harness connector
(to Spiral Cable Sub-assembly)
- -



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L29-1 (D+) - Body ground Ignition switch ON Below 1 V
L29-2 (D-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L29-1 (D+) - L29-2 (D-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L29-1 (D+) - L29-2 (D-) Always 1 MΩ or higher



j.

Restore the released activation prevention mechanism of connector B to its original condition.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L29-1 (D+) - Body ground Always 1 MΩ or higher
L29-2 (D-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY

NG

6.CHECK COWL WIRE
6.CHECK COWL WIRE
a.

Disconnect the instrument panel wire connector from the cowl wire.

C367990C01
4,0.688 4.375,0.906 0.375,0.219 5.479,0.698 5.854,0.917 0.375,0.219 4.396,1.417 4.688,1.146 true 5.042,1.125 5.333,1.406 true 5.875,1.135 6.26,0.917 true 6.479,0.917 6.865,1.156 true 4.333,0.094 4.646,0.25 0.313,0.156 10 false *A 5.844,0.104 6.156,0.26 0.313,0.156 10 false *B 0.198,0.458 0.51,0.615 0.313,0.156 10 false *1 1.156,1.052 1.469,1.208 0.313,0.156 10 false *2 3.115,1.344 3.427,1.5 0.313,0.156 10 false *3 1.979,0.385 2.292,0.542 0.313,0.156 10 false *4 2.417,0.375 2.729,0.531 0.313,0.156 10 false *5 4.156,0.083 4.469,0.24 0.313,0.156 10 false *a 5.667,0.094 5.979,0.25 0.313,0.156 10 false *a 4.792,0.24 5.115,0.396 0.323,0.156 10 false *6 6.302,0.292 6.625,0.448 0.323,0.156 10 false *6 4.094,0.708 4.406,0.865 0.313,0.156 10 false IL4 5.594,0.729 5.906,0.885 0.313,0.156 10 false IL7 2.573,0.854 2.885,1.073 0.313,0.219 10 false B 2.969,0.604 3.281,0.823 0.313,0.219 10 false A 2.323,0.854 2.635,1.073 0.313,0.219 10 false C 2.125,0.854 2.438,1.073 0.313,0.219 10 false D 1.875,0.854 2.188,1.073 0.313,0.219 10 false E 1.656,0.854 1.969,1.073 0.313,0.219 10 false F 0.719,0.854 1.031,1.073 0.313,0.219 10 false G 0.49,0.854 0.802,1.073 0.313,0.219 10 false H 4.26,1.448 4.573,1.604 0.313,0.156 10 false D+ 5.365,1.448 5.677,1.646 0.313,0.198 10 false D- 5.708,1.135 6.021,1.333 0.313,0.198 10 false D+ 6.865,1.177 7.115,1.406 0.25,0.229 10 false D-
*A for LHD *B for RHD
*1 Horn Button Assembly *2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly *4 Instrument Panel Wire
*5 Cowl Wire *6 Connector C
*a Front view of wire harness connector
(to Instrument Panel Wire)
- -



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
IL4-1 (D+) - Body ground Ignition switch ON Below 1 V
IL4-2 (D-) - Body ground Ignition switch ON Below 1 V

for RHD
Tester Connection Switch Condition Specified Condition
IL7-1 (D+) - Body ground Ignition switch ON Below 1 V
IL7-2 (D-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
IL4-1 (D+) - IL4-2 (D-) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
IL7-1 (D+) - IL7-2 (D-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
IL4-1 (D+) - IL4-2 (D-) Always 1 MΩ or higher

for RHD
Tester Connection Condition Specified Condition
IL7-1 (D+) - IL7-2 (D-) Always 1 MΩ or higher



j.

Restore the released activation prevention mechanism of connector B to its original condition.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
IL4-1 (D+) - Body ground Always 1 MΩ or higher
IL4-2 (D-) - Body ground Always 1 MΩ or higher

for RHD
Tester Connection Condition Specified Condition
IL7-1 (D+) - Body ground Always 1 MΩ or higher
IL7-2 (D-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL WIRE

NG

REPLACE COWL WIRE