Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.08–2022.09
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0138307 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1627/82  Lost communication with Side Airbag Sensor LH  B1628/82  Side Airbag Sensor Assembly LH Initialization Incomplete  


DESCRIPTION

The door side airbag sensor LH circuit consists of the airbag sensor assembly and door side airbag sensor LH.

The door side airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag should be deployed.

DTC B1608, B1617/84, B1618/84 is stored when a malfunction is detected in the door side airbag sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1627/82 Lost communication with Side Airbag Sensor LH One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the door side airbag sensor LH circuit for 2 seconds.

·

A door side airbag sensor LH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Door side airbag sensor LH

·

Airbag sensor assembly


B1628/82 Side Airbag Sensor Assembly LH Initialization Incomplete One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the door side airbag sensor LH circuit for 2 seconds.

·

A door side airbag sensor LH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Door side airbag sensor LH

·

Airbag sensor assembly



WIRING DIAGRAM

C305104E17
1.208,0.896 1.823,1.094 0.615,0.198 10 false BBL+ 1.208,2.073 1.823,2.271 0.615,0.198 10 false BBL- 5.615,0.896 7.156,1.094 1.542,0.198 10 false BBL+ 5.615,2.073 7.156,2.271 1.542,0.198 10 false BBL- 0.396,2.979 2.75,3.375 2.354,0.396 10 false Door Side Airbag Sensor LH 5.365,2.958 7,3.438 1.635,0.479 10 false Airbag Sensor Assembly 5.365,2.792 6.906,2.99 1.542,0.198 10 false S24 0.396,2.813 1.938,3.01 1.542,0.198 10 false S26 1.688,0.792 3.229,0.99 1.542,0.198 10 false 2 1.698,1.958 3.24,2.156 1.542,0.198 10 false 1 5.427,0.802 6.969,1 1.542,0.198 10 false 8 5.323,1.958 6.865,2.156 1.542,0.198 10 false 15

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor LH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

2.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and door side airbag sensor LH.


b.
C326156C02
0.656,1.458 0.969,1.615 0.313,0.156 10 false *1 2.615,1.531 2.927,1.688 0.313,0.156 10 false *2 1.563,0.656 1.875,0.813 0.313,0.156 10 false *3
*1 Door Side Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Floor Wire


Check that the connectors (on the airbag sensor assembly side and door side airbag sensor LH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

3.CHECK FLOOR WIRE

The connectors are deformed or damaged

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C363914C01
2.792,0.719 3.198,0.958 0.406,0.24 4.927,0.719 5.333,0.958 0.406,0.24 3.708,0.885 3.385,1.396 3.385,1.396 3.229,1.396 true 3.906,0.885 4.188,1.396 4.188,1.396 4.375,1.396 true 6.094,1.385 6.281,1.594 6.281,1.594 6.406,1.594 true 1.792,0.802 1.948,1 0.156,0.198 10 false A 1.417,1.042 1.573,1.24 0.156,0.198 10 false B 1.01,1.042 1.167,1.24 0.156,0.198 10 false C 0.635,0.813 0.792,1.01 0.156,0.198 10 false D 1.906,1.26 2.063,1.458 0.156,0.198 10 false *2 1.177,0.594 1.333,0.792 0.156,0.198 10 false *3 3.719,0.167 3.875,0.365 0.156,0.198 10 false *a 5.802,0.073 5.958,0.271 0.156,0.198 10 false *b 4.354,0.802 4.51,1 0.156,0.198 10 false *4 6.49,0.802 6.74,1 0.25,0.198 10 false *5 2.823,1.302 3.229,1.5 0.406,0.198 10 false BBL- 4.458,1.302 4.865,1.5 0.406,0.198 10 false BBL+ 0.573,1.188 0.729,1.385 0.156,0.198 10 false *1 6.458,1.49 6.708,1.688 0.25,0.198 10 false *6 2.865,0.76 3.271,0.958 0.406,0.198 10 false S26 5.021,0.76 5.427,0.958 0.406,0.198 10 false S24
*1 Door Side Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Floor Wire *4 Connector C
*5 Connector B *6 Service Wire
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S26-2 (BBL+) - Body ground Ignition switch ON Below 1 V
S26-1 (BBL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S26-2 (BBL+) - S26-1 (BBL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S26-2 (BBL+) - S26-1 (BBL-) Always 1 MΩ or higher
S26-2 (BBL+) - Body ground Always 1 MΩ or higher
S26-1 (BBL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK DOOR SIDE AIRBAG SENSOR LH

NG

REPLACE FLOOR WIRE

4.CHECK DOOR SIDE AIRBAG SENSOR LH
a.
C326158C02
1.052,1.458 1.365,1.615 0.313,0.156 10 false *1 2.365,1.573 2.677,1.729 0.313,0.156 10 false *2
*1 Door Side Airbag Sensor RH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly.


b.

Interchange the door side airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 63

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 63
Result:
Result Proceed to
DTC B1627/82 or B1628/82 is output A
DTC B1622/81 or B1623/81 is output B
DTC B1622/81, B1623/81, B1627/82 and B1628/82 are not output C


HINT:

Codes other than DTC B1622/81, B1623/81, B1627/82 and B1628/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.



A

B

C