41110F 1.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY
Remove any dust and oil from the front differential carrier assembly and the contact surfaces of the axle housing.
Install a new gasket.
Install the front differential carrier assembly with the 10 nuts and 10 washers.
| *A | Nut Type A |
| *B | Nut Type B |
As there are 2 types of nuts, the same type nut must be used during removal and installation.
Remove any foreign matter (dirt, gasket remains, metal particles, etc.) from the contact surfaces of the housing and differential carrier and install a new gasket.
2.INSTALL FRONT AXLE SHAFT ASSEMBLY
3.INSTALL FRONT BRAKE TUBE (w/o ABS)
for 1HZ:
| *a | Torque Wrench Fulcrum Length | - | - |
Install the brake tube, 3-way joint and brake hose with the 4 bolts.
Using a union nut wrench, connect each brake tube to the flexible hose while holding the flexible hose with a wrench.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)
Install the brake tube with a new clip.
for 1GR-FE:
| *a | Torque Wrench Fulcrum Length | - | - |
Install the brake tube, 3-way joint and brake hose with the 4 bolts.
Using a union nut wrench, connect each brake tube to the flexible hose while holding the flexible hose with a wrench.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)
Install the brake tube with a new clip.
4.INSTALL FRONT BRAKE TUBE (w/ ABS,VSC)
for 1HZ, 1VD-FTV:
| *a | Torque Wrench Fulcrum Length | - | - |
Install the brake tube with the 5 bolts.
Using a union nut wrench, connect each brake tube to the flexible hose while holding the flexible hose with a wrench.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)
Install the brake tube with 2 new clips.
for 1GR-FE:
| *a | Torque Wrench Fulcrum Length | - | - |
Install the brake tube with the 3 bolts.
Using a union nut wrench, connect each brake tube to the flexible hose while holding the flexible hose with a wrench.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)
37140 5.INSTALL FRONT PROPELLER SHAFT ASSEMBLY
6.ADD DIFFERENTIAL OIL