Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY (for Single Cab) › 2016.08–2022.09
RM25T0E _58 Vehicle Interior _029931 SEAT BELT _0142807 FRONT SEAT OUTER BELT ASSEMBLY(for Single Cab) A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY(for Single Cab)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 73200A 1.INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY (w/ Pretensioner and Force Limiter)

a.
B456590

Attach the guide and install the front shoulder belt anchor adjuster assembly with the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73220 2.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

a.

w/o Pretensioner and Force Limiter:

i.
B386634C02
1.083,1.646 1.74,1.729 true 1.771,0.521 0.958,0.229 true 0.771,0.125 1.083,0.281 0.313,0.156 10 false *a 0.896,1.542 1.208,1.698 0.313,0.156 10 false *b
*a Bolt A
*b Bolt B


Attach the guide and temporarily install the front seat outer belt assembly LH with the bolt (A) and (B).

NOTICE:

When installing the retractor, make sure the guides of the vehicle only contact the installation areas of the retractor.


Torque:
for Bolt A : 5.0 N*m (51 kgf*cm, 44 in.*lbf)
for Bolt B : 42 N*m (428 kgf*cm, 31 ft.*lbf)


ii.

Connect the shoulder anchor of the front seat outer belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


iii.

Attach the 2 claws to close the front seat outer belt shoulder anchor cover.


iv.

Connect the floor anchor of the front seat outer belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



b.

w/ Pretensioner and Force Limiter:

i.
B457954C01
0.906,0.302 1.615,0.156 true 2.385,0.656 2.76,0.229 true 2.802,2.927 2.406,2.458 true 1.656,0.031 1.969,0.188 0.313,0.156 10 false *a 2.792,0.063 3.104,0.219 0.313,0.156 10 false *b 2.813,2.948 3.125,3.104 0.313,0.156 10 false *c
*a Locking Button
*b Bolt A
*c Bolt B


Attach the 2 guides and temporarily install the front seat outer belt assembly LH with the bolt (A) and (B).

NOTICE:

When installing the retractor, make sure the guides of the vehicle only contact the installation areas of the retractor.


Torque:
for Bolt A : 5.0 N*m (51 kgf*cm, 44 in.*lbf)
for Bolt B : 42 N*m (428 kgf*cm, 31 ft.*lbf)


ii.

Check that the cable is disconnected from the negative (-) battery terminal.


iii.

Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTICE:

Securely lock the locking button.



iv.

Connect the shoulder anchor of the front seat outer belt assembly LH with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



c.

Check that the front seat outer belt is not twisted.


d.

Check that the ELR locks.

NOTICE:

The check should be performed with the front seat outer belt assembly LH installed.


i.

With the belt assembly installed, check that the belt locks when it is pulled out quickly.



Hide 73024 3.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH (w/ Pretensioner and Force Limiter)

a.
B452003

Attach the 6 guides to install the front shoulder belt anchor plate sub-assembly LH.


Hide 62412 4.INSTALL CENTER PILLAR GARNISH LH (w/ Pretensioner and Force Limiter)

Hide 62316C 5.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH (w/ Pretensioner and Force Limiter)

Hide 67914 6.INSTALL FRONT DOOR SCUFF PLATE LH (w/ Pretensioner and Force Limiter)

Hide 73174 7.INSTALL FRONT SEAT BELT HOLE COVER LH (w/o Pretensioner and Force Limiter)

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Pretensioner and Force Limiter)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 9.CHECK SRS WARNING LIGHT (w/ Pretensioner and Force Limiter)